Search tips
Showing 251 results View by: Thread Post Sort by
    Answered

  • LAUNCHXL2-RM57L: RM57L

    Resolved
    Part Number: LAUNCHXL2-RM57L Other Parts Discussed in Thread: HALCOGEN Does anyone know of a reference project for CAN bus for the LaunchXL2-RM57L? Thanks in advance for all help.
    • Resolved

  • LAUNCHXL2-RM57L: WHAT IS THE INTERNAL VOLTAGE REFERENCE FOR ADC

    TI Thinks Resolved
    Part Number: LAUNCHXL2-RM57L Other Parts Discussed in Thread: HALCOGEN Hi TI Team, I am currently working on ADC project on LAUNCHXL2-RM57L.It may be a chilly question i am just a beginner.What is the internal reference voltage of the adc.Is there…

  • LAUNCHXL2-RM57L: After EMACTXHdrDescPtrWrite, no packet on the wire

    Part Number: LAUNCHXL2-RM57L Other Parts Discussed in Thread: HALCOGEN I am working on a network interface for FreeRTOS, generated board package with HalCoGen. The basic setting is MDIO, EMAC, SCI1 enabled, MPU disabled. Rx and Tx interrupt enabled…
    • Answered

  • LAUNCHXL2-RM57L: RM57L843

    Resolved
    Part Number: LAUNCHXL2-RM57L Other Parts Discussed in Thread: DP83630 , HALCOGEN Hi, I am using Hercules RM57Lx Launchpad Development Kit and I want use Ethernet Protocol. I am new to Ethernet so I decided first by using MDIO module to read the Phy…
    • Resolved

  • LAUNCHXL2-RM57L: LAUNCHXL2-RM57L

    Part Number: LAUNCHXL2-RM57L Dear TI, I have the same question as in TMS570LS1224: FEE addressable driver - Arm-based microcontrollers forum - Arm-based microcontrollers - TI E2E support forums I want to write my own driver for Emulated EEPROM usage…
    • Answered

  • LAUNCHXL2-RM57L: Information on RM57 MPU and DMA Software Set Up and Usage

    Resolved
    Part Number: LAUNCHXL2-RM57L Other Parts Discussed in Thread: HALCOGEN Hello, We are using the RM57 launchpad board. Where can our team find more information on setting up and using RM57 MPU and DMA on the RM57 in the software (i.e., HalCoGen or CCS…
    • Resolved
    • Answered

  • LAUNCHXL2-RM57L: Making the LIN2/SCI2 work as SCI2 (UART) with interrupts

    Resolved
    Part Number: LAUNCHXL2-RM57L Other Parts Discussed in Thread: HALCOGEN Hi, I am trying to make the LIN2/SCI2 work as SCI2 (UART) with interrupts. I got something running but only partial success. When transmitting, only got interrupts for the first…
    • Resolved
    • Answered

  • LAUNCHXL2-RM57L: RM57 TI CCS ARM-CGT vs ARM-CGT-CLANG

    Resolved
    Part Number: LAUNCHXL2-RM57L Other Parts Discussed in Thread: ARM-CGT , HALCOGEN Hello, I understood that TI's CCS has two different versions of code generation tools that are available depending on the processor family: CCS ARM-CGT and the ARM-CGT…
    • Resolved

  • RE: LAUNCHXL2-RM57L: Issue Configuring MibSPI2 with External SPI SD Card Reader

    Hi Micheal, Michael Dean said: Still hoping there is some example project or further info that can be referenced or recommended as my pin setup looks to be correct then but am still not seeing replies from MISO when MOSI is sending out the proper SPI…
    • Answered

  • RE: LAUNCHXL2-RM57L: Config the SPI3 to access the AT25080 SPI EEPROM on the Aardvard I2C/SPI activity board

    Resolved
    Hi Helen, I observed one conflict here, Helen Chen said: 3CS1 Here you said you are using 3CS1 right? Helen Chen said: gioSetBit(spiPORT3, SPI3_CS0, LOW); But why you are operating 3CS0? -- Thanks & regards, Jagadish.

Didn't find what you are looking for? Post a new question.