• LMH0002: fpga GTPs and lmh0002 cable driver interface support

  

  anusha kodali

  TI Thinks Resolved

  Part Number: LMH0002 Tool/software: for providing output of the SMPTE 292M video data from the FPGA we want the physical layer interface between FPGA and coaxial cable for that we want to use the LMH0002 cable driver. we want to conformation about that…

  • over 1 year ago
  • Interface
  • Interface forum
Answered

• LMH0002: Coax line voltage for LMH0002

  

  Navneet Gandhi

  Resolved

  Part Number: LMH0002 Other Parts Discussed in Thread: CLC007 , CLC006 , LMH1297 Hi, 1. The datasheet for LMH0002 (on page 3) mentions the Output voltage swings of between 750mVpp to 1100 mVpp. Is it correct to assume that this is the nominal range of…

  • Resolved

  • over 2 years ago
  • Interface
  • Interface forum

• LMH0002: Output Level

  

  user6308822

  TI Thinks Resolved

  Part Number: LMH0002 Tool/software: Hello, Team We have a question about LMH0002SQ. We use LMH0002SQE/NOPB for ASI driver. In the specifications, the output (Vsdo) is written as 750 to 850mV (p-p) under the conditions (REF=750Ω1%). When measured with…

  • over 1 year ago
  • Interface
  • Interface forum

• LMH0002: LMH0002 and LMH0044

  

  Amy Luo

  TI Thinks Resolved

  Part Number: LMH0002 Other Parts Discussed in Thread: LMH0044 , , LMH0324 Hi team, Whether LMH0002 and LMH0044 can transmit LVDS signals with rate of 100M at least 100m distance. If not, can you recommend a solution? Thank you in advance. Best wishes…

  • over 5 years ago
  • Interface
  • Interface forum

• LMH0002: Application scenario problem for LMH0002

  

  user5191502

  TI Thinks Resolved

  Part Number: LMH0002 I want to know that if LMH0002 can be used to transmit a single pulse over long distances(about 100 meters)?

  • over 5 years ago
  • Interface
  • Interface forum
Answered

• LMH0002: to support MADI Compatibility

  

  K.Yaita

  Resolved

  Part Number: LMH0002 Other Parts Discussed in Thread: LMH1218 Hi Team, My customer wants to use LMH0002 with supporting MADI. Can he also apply the following 6-dB passive attenuator block? https://www.ti.com/lit/an/snla299/snla299.pdf Best Regards, Y…

  • Resolved

  • over 4 years ago
  • Interface
  • Interface forum

• LMH0002: LMH0002 DVB-ASI

  

  user5041399

  TI Thinks Resolved

  Part Number: LMH0002 Refer to the Typical Application on the datasheet / SDO (Serial data complement output) side output is BNC connected Although there are devices that can recognize signals and devices that can not be recognized. / SDO is negative…

  • over 7 years ago
  • Interface
  • Interface forum
Answered

• LMH0002: interfacing with DS10CP152

  

  plenet remi

  Resolved

  Part Number: LMH0002 Other Parts Discussed in Thread: DS10CP152 , Hi, I would like to interface OUT0+- from DS10CP152 (crosspoint switch) to SDI/nSDI input from LMH0002 cable driver, could you please advise how to proceed (capacitor? resistor ? network…

  • Resolved

  • over 6 years ago
  • Interface
  • Interface forum
Answered

• LMH0002: Can RREF be set to reduce output amplitude to between 300mVpp and 600mVpp SE?

  

  jt

  Resolved

  Part Number: LMH0002 Other Parts Discussed in Thread: LMH0397 Is there an RREF value that would allow reducing the SE output swing to be between 300mVpp and 600mVpp? Regards, Josh

  • Resolved

  • over 8 years ago
  • Interface
  • Interface forum
Answered

• LMH0002 / RREF resistor

  

  S.Satoshi

  Resolved

  Other Parts Discussed in Thread: LMH0002 , LMH0302 , LMH0303 Hi, Team, I know that the newer devices like LMH0302 or LMH0303 recommend to use only 750ohm and specify the VSDO with only RREF = 750ohm 1%. However LMH0002 specify the VSDO with RREF …

  • Resolved

  • over 12 years ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.