Search tips
Showing 39 results View by: Thread Post Sort by
    Answered

  • LP-CC1312R7: 32kHz calculations and DC-DC converter coil for CC1312R7

    Resolved
    Part Number: LP-CC1312R7 Other Parts Discussed in Thread: CC1312R7 Hi I am looking at the require analog adjustment to customise the reference design LP-CC1312R7 and accommodate some of the parts we are using in other designs. Regarding the 32kHz xtal…
    • Resolved
    • Answered

  • RE: LP-CC1312R7: Can't join network with other board

    Resolved
    As seen with Sid, Border router and node weren't able to perform EAP-TLS process with EU band, I had to switch with NA band, it is working now. Thank you everyone for your valuable help and your patience. Best regards Ben
    • Answered

  • LP-CC1312R7: RSSI vs time get stuck & TX carrier drift during temperature test.

    Resolved
    Part Number: LP-CC1312R7 Other Parts Discussed in Thread: WMBUS , CC1312R Hi while measuring RSSI vs time (Rx continuous), i observed that the RSSI reading for the LP-CC1312R7 get stuck after some time. i.e. changing the signal level does not result…
    • Resolved

  • LP-CC1312R7: Measure the current draw during operation

    Part Number: LP-CC1312R7 Other Parts Discussed in Thread: CC1200 , WMBUS , CC1312R7 , SEGGER Hi Team, Our customer would like to measure the current draw during operation of the wireless LP-CC1312R7 Launchpad. According to our customer, The supply domain…
    • Answered

  • LP-CC1312R7: wmbus MTO rx not working properly while wmbus OTM rx is working with the same payload, sync word and CRC

    Resolved
    Part Number: LP-CC1312R7 Other Parts Discussed in Thread: WMBUS , , CC1312R7 , CC1101 , CC1200 Hi, I have successfully performed rx measurements on Wmbus OTM sending packets either between 2 boards or between an ESG 4438C signal generator and a LP-CC1312R7…
    • Resolved
    • Answered

  • CC1311R3: CC1311R3 5x5 reference design of EU/US band

    Resolved
    Part Number: CC1311R3 Other Parts Discussed in Thread: CC1312R7 , LP-CC1312R7 , CC1310 , CC1352P7 Hi there, do you have the CC1311R3 5x5 reference design of EU/US band? thanks. BR. Albin
    • Resolved

  • RE: CC1312R7: TI network stack receives incorrect 802.15.4 frames from Contiki-NG

    The TI capture is running on LP-CC1312R7, and the Contiki-NG capture on LP-CC1312R1 (as R7 is not supported out of the box) Here are the custom radio params for Contiki-NG, in case any of this is of interest. # Channel configuration DEFINES += DOT_15_4G_CONF_FREQ_BAND_ID…

  • RE: LAUNCHXL-CC1352R1: TI WiSUN: How to run Border Router Example into this evl kit.

    Hi Karun, You need a 704Kb Flash device to run the border router example. These are CC1312R7, CC1352P7 devices. You cannot flash the LP_CC1312R7 project on a CC1352R1 which only has 352KB of flash. Please use a CC1312R7 launchpad for the project that…
    • Answered

  • RE: CC1312R: how to enable Sysyconfig CCFG Configuration at SDK 6.41?

    Resolved
    Hi CK, It is done on purpose, because CCFG has to be configured through the BIM project, the explanations are there: https://e2e.ti.com/support/wireless-connectivity/bluetooth-group/bluetooth/f/bluetooth-forum/997343/cc2652r-enable-ptm-bsl-backdoor-in…

  • RE: CC1312R7: WI-SUN NETWORK IN QUITO - ECUADOR

    Hi Mario, Please use ti.com for ordering the kits. https://www.ti.com/tool/LAUNCHXL-CC1352P https://www.ti.com/tool/LP-CC1312R7 Regards, Sid

Didn't find what you are looking for? Post a new question.