TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
    • Analog
    • Automotive
    • DLP® technology
    • Embedded processing
    • Industrial
    • Power management
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 293 results View by: Thread Post Sort by
  • MAX232E: MAX232E

    kaipun wong
    kaipun wong
    TI Thinks Resolved
    Part Number: MAX232E I would like to use the MAX232E to interface to the PC serial port. I used 10uF ceramic cap for C1-C4. The waveform for C1+ was from 5V to 10V, C1- was 0V to 5V, C2+ was 0V to 10V and C2- was 0V to -10V. VS+ was 8V while VS- was …
    • 3 months ago
    • Interface
    • Interface forum
  • MAX232: Replacement from SN75188NSRG4 to MAX232NS

    Noriyuki Takahashi
    Noriyuki Takahashi
    Part Number: MAX232 Hi team, In customer's sysytem, SN75188NSRG4 has been used, but c ustomer is considering to repalce SN75188NSRG4 with MAX232NS in next project. Are there any concerns they need to take care about? +/-12V is applied to SN75188NSRG4…
    • 27 days ago
    • Interface
    • Interface forum
  • Answered
  • MAX232E: Connect other pcb dout signals

    user5093781
    user5093781
    Resolved
    Part Number: MAX232E Other Parts Discussed in Thread: TRS208 , MAX208 Hi. Please see the attached file. I want to connect PCB1 DOUT1 and PCB2 DOUT1. Is it possible? If it isn't possible, do you have any ideas? Besr regards. MAX232E_question.xlsx
    • Resolved
    • 30 days ago
    • Interface
    • Interface forum
  • Answered
  • MAX232: Absolute Maximun Sink Current of TxOUT and RxOUT

    Shinichi Inoue
    Shinichi Inoue
    Resolved
    Part Number: MAX232 Dear specialists, My customer is considering MAX232IDR and has a question. I would be grateful if you could advise. --- What is the maximum rating of the sink current of the driver / receiver OUT terminal? I looked at the data sheet…
    • Resolved
    • 22 days ago
    • Interface
    • Interface forum
  • MAX232: MAX232IDR p spice model required

    KAUSHAL SHARMA1
    KAUSHAL SHARMA1
    Part Number: MAX232 Hi support team I need the spice simulation model of MAX232IDR BR Kaushal
    • 1 month ago
    • Interface
    • Interface forum
  • MAX232: MAX232

    Pavaman Panchamukhi
    Pavaman Panchamukhi
    TI Thinks Resolved
    Part Number: MAX232 Hi I am using 10uF Al El Cap with ESR and Ripple rate of 10 ohm and 60mArms. Now I need to change to 16ohms & 75mArms ripple current. Will it cause any data rate malfunction because of change in Ripple current and ESR.
    • 11 months ago
    • Interface
    • Interface forum
  • Answered
  • MAX232: Connect T1OUT to T2IN / R1OUT to R2IN to invert signal

    Takahiro Saito
    Takahiro Saito
    Resolved
    Part Number: MAX232 Other Parts Discussed in Thread: SN74LVC2G04 Hi team, My customer is going to connect T1OUT to T2IN and R1OUT to R2IN to invert the signal. Could you check it will not cause the damage of device? Regards, Saito
    • Resolved
    • 7 months ago
    • Interface
    • Interface forum
  • MAX232: data rate when C1 = C2 = 0.085uF

    Noriyuki Takahashi
    Noriyuki Takahashi
    TI Thinks Resolved
    Part Number: MAX232 Hi team, Could you tell the data rate when C1 = C2 = 0.085uF? They need 12kbps at max but C1 and C2 are 0.085uF. So they are not sure this is OK, because C1 and C2 are 1uF at the condition of the datasheet. Could you give any suggestion…
    • over 1 year ago
    • Interface
    • Interface forum
  • MAX232: TI solution suggestion

    Jimmy Lai
    Jimmy Lai
    Part Number: MAX232 Other Parts Discussed in Thread: LM324 , Dear Team, Do we have solution is that integrates function of MAX232 and LM324 ? Many Thanks, Jimmy
    • over 1 year ago
    • Interface
    • Interface forum
  • Answered
  • MAX232: Are these possible to use charge pump capacitor(C1-C4) is 2.2uF

    Shinichi Inoue
    Shinichi Inoue
    Resolved
    Part Number: MAX232 Dear Specialists, My customer is considering MAX232ID and has a question. I would be grateful if you could advise. --- According to the datasheet, charge pump capacitor(C1 to C4) should use 1.0uF of ceramic, Tantalum or electrolytic…
    • Resolved
    • over 1 year ago
    • Interface
    • Interface forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question
About TI
Company News & events Investor relations Corporate citizenship Careers Contact us
Quick links
TI E2E™ design support forums Customer support center Packaging Quality & reliability TI university program myTI FAQ
Buying
Ordering resources Ordering help & FAQs BOM & cross reference tool Quick add to cart Authorized distributors
Connect with us

Texas Instruments has been making progress possible for decades. We are a global semiconductor company that designs, manufactures, tests and sells analog and embedded processing chips. Our products help our customers efficiently manage power, accurately sense and transmit data and provide the core control or processing in their designs.

Cookie policy Privacy policy Terms of sale Terms of use Trademarks Website feedback

© Copyright 1995-2021 Texas Instruments Incorporated. All rights reserved.