Search tips
Showing 305 results View by: Thread Post Sort by

  • MSP430F2370: behavior on power switch on

    Part Number: MSP430F2370 Hi Team For MSP430F2370IRHA,what happens whith system reset and initialization when the power level on "Vcc" and on "RST/NMI"-Pin increase at the same time and the same power level? Does a Brownout Reset (BOR) occur or get the…

  • MSP430F2370: Regarding Reading and Writing data for NFC peer to peer communication using TRF7970A

    TI Thinks Resolved
    Part Number: MSP430F2370 Other Parts Discussed in Thread: TRF7970A , Hello, ''I am not able to read and send the data (NFC peer to peer communication) using two TRF7970A devices, please provide a solution'' I have referred to the document…

  • RE: MSP430F2370: MSPF2370 - Problems with DCO Constants

    Hello Simon, Looking back through some older threads and realized this one was never closed out. I see you were talking with Dennis in the other thread, were you able to find a work around for your issue? Thanks, JD

  • RE: MSP430F2370: Wrong DCO constants after flashing

    Hi Simon, For for the long delay on this. Can you provide an example of the DCO calibration values on a good unit and on one where the resulting frequencies are not correct?

  • RE: MSP430F2370: ISR Trap in Application code SLOA214 for Special Direct Mode With the TRF7970A

    I would suggest not mixing signed/unsigned arithmetic in that subtraction (since the distinction appears when crossing 0, which is the case you're interested in), but I defer to you on that. Did your "mousetrap" catch anything?

  • CCS/MSP430F2370: GIE get cleared during program step under debug

    Part Number: MSP430F2370 Tool/software: Code Composer Studio Hi, I use MSP43F2370 with MSP-FETFlash Emulation Tool. I figured out that GIE gets cleared during program step execution under debug. As I searched at TI e2e forum this problem long time exists…
    • Answered

  • MSP430F2370: MSP430P325AIPM

    Resolved
    Part Number: MSP430F2370 I am trying to find what the X prefix means at the end of part number. MSP430P325AIPM is actual call out. Have seen the MSP430P325AIPMX does the X denote anything? not seen on Data sheet. Thanks Ray
    • Resolved

  • MSP430F2370: TimerB1, TimerB2 CCIFG set to 1 automaticaly when CCIE is set to 0 causing ISR trap.

    Part Number: MSP430F2370 Other Parts Discussed in Thread: TRF7970A , Hi, I am using MSP430F2370 with TRF7970A. I am using code based on sloa214. In sloa214 TimerA0 used for RFID read APIs for timeout but in modified code we used TimerA0 for Application logic…

  • TRF7970A: Porting from MSP430G2553 to MSP430F2370

    TI Thinks Resolved
    Part Number: TRF7970A Other Parts Discussed in Thread: MSP430F2370 , Hi, I have a custom board based on MSP430F2370 and TRF7970A . I'm modifying the www.ti.com/.../sloc297 code which is for MSP430G2553 to work with MSP430F2370 . Want to know if I have to take…

  • MSP430F2370: Uart communication problem

    TI Thinks Resolved
    Part Number: MSP430F2370 Other Parts Discussed in Thread: TRF7970A , Hi, I have a custom board based on MSP430F2370 and TRF7970A. The TRF7970A has a 13.56MHz crystal and SYS_CLK of TRF7970A is connected to XIN of MSP430F2370. The TRF7970A SYS_CLK output…

Didn't find what you are looking for? Post a new question.