Answered

• MSP430F2417: I/O states during 'pre-programming'/'programming'/'reprogramming'

  

  Michael T Schneider

  Resolved

  Part Number: MSP430F2417 Team, Looking for a few answers on the MSP430F2417TPM: What is the state of output signals when the MSP has been programmed but is being held in reset? What is the state of output signals when the MSP is being reprogrammed through…

  • Resolved

  • 8 months ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum
Answered

• MSP430F2417: Unexpected PUC (Resolved)

  

  Raymond Wales

  Resolved

  Part Number: MSP430F2417 Another obscure problem solved: I am sharing this in the hope that it helps somebody. A new project with a part (F2417) which I have used loads of times before was restarting occasionally with unexpected PUC. This would occur…

  • Resolved

  • over 1 year ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

• CCS/MSP430F2417: Reset error using dual image in RAM and ROM

  

  Parama Sivan

  TI Thinks Resolved

  Part Number: MSP430F2417 Tool/software: Code Composer Studio Hi, I have used ram memory for bootloader image and flash memory for application firmware. The application firmware creates a copy of the flash image into an external EEPROM and switches into…

  • over 1 year ago
  • Code Composer Studio™︎
  • Code Composer Studio forum
Answered

• CCS/MSP430F2417: .Bin file creation for MSP430 in CCS 9.2 v

  

  Parama Sivan

  Resolved

  Part Number: MSP430F2417 Tool/software: Code Composer Studio Hi, I couldn't find the correct way to generate the .bin file from the intel .hex format or .out file. I have tried the following way in my project settings, but it throws error during compilations…

  • Resolved

  • over 1 year ago
  • Code Composer Studio™︎
  • Code Composer Studio forum
Answered

• MSP430F2417: Running slowly even though XT2 running at 16 MHz

  

  Raymond Wales

  Resolved

  Part Number: MSP430F2417 Not a question - a solution that might help others. It took me a long time to hunt this one down. In my application, the XT2 oscillator is driving a 16 MHz crystal. It is started after the SVS reports that there is sufficient…

  • Resolved

  • over 1 year ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum
Answered

• RE: DRV8886: what is the root cause why DVDD pin output only 1.5v and AVDD pin output remain 0v?

  

  Pablo Armet

  Resolved

  Hi Lin, This is interesting. Can you repeat the experiment above and measure all the pins of the JTAG pins of the DRV8886EVM. Give me a day to look at the IAR error message to see if it gives any clues as to what is happening. What I want to understand…

  • 4 months ago
  • Motor drivers
  • Motor drivers forum
Answered

• MSP430F2417 RTC using DS2417

  

  rupesh vishwakarma

  Resolved

  Other Parts Discussed in Thread: MSP430F2417 HI , I want to interface REAL time chip DS2417 1 wire with MSP430F2417 my confusion is how to know the GPIO of MSP whether it is pushpull or open drain ,I need to configure GPIO 2.1 as open drain can any one…

  • Resolved

  • over 11 years ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

• MSP430F2618: The documentation is ambiguous regarding Main Flash Memory segments

  

  Atlant Schmidt

  TI Thinks Resolved

  Part Number: MSP430F2618 Other Parts Discussed in Thread: MSP430F2416 , MSP430F2417 , MSP430F2418 , MSP430F2419 , MSP430F2617 , MSP430F2619 The MSP430F2618 is "casually" described as having 116 KB of Main Flash memory but if you look at the address…

  • over 2 years ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

• CCS/CCSTUDIO: Jtag support for CCstudio v7.0

  

  Nirmal Gutty

  TI Thinks Resolved

  Part Number: CCSTUDIO Other Parts Discussed in Thread: MSP-FET , MSP430F2417 Tool/software: Code Composer Studio Does CC Studio V 7.0 have JTAG support for MSP430 USB - Debug- Interface MSP-FET430UIF?

  • over 3 years ago
  • Code Composer Studio™︎
  • Code Composer Studio forum
Answered

• RE: CCS/MSP430G2202: MSP430G2102's Supply Voltage Supervisor (SVS) module configuation issue

  

  Clemens Ladisch

  Resolved

  Chapter 9 of the User's Guide says: The SVS is implemented in selected MSP430x2xx devices. None of them is in the G2xx "value line": MSP430AFE221, MSP430AFE231, MSP430AFE233, MSP430AFE253, MSP430F233, MSP430F235, MSP430F2416, MSP430F2417, MSP430F2418…

  • over 3 years ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

Didn't find what you are looking for? Post a new question.