Search tips
Showing 30 results View by: Thread Post Sort by

  • RE: MSP430F5242: JTAG Mode

    Have you try to capture the normal signals that using CCS or uniflash? I can compare with it and may get the hint.

  • MSP430F5242: I am currently using the MSP430F5242 to read/write SD cards via SPI.

    TI Thinks Resolved
    Part Number: MSP430F5242 Hi, Good Day. I have a customer who is working with MSP430F5242. Please see below his query for your reference. Thank you very much. I am currently using the MSP430F5242 to read/write SD cards via SPI. I am also using FatFs -…

  • MSP430F5242: Bootloader/BSL Entry Sequence and Operation..

    Part Number: MSP430F5242 Other Parts Discussed in Thread: MSP-FET Hi Team MSP, A few questions on the bootloader for the F5242 WRT the F5242 Datasheet & SLAU319. We are having trouble starting the BSL/Bootloader on the F5242. We put the F5242 into…

  • MSP430F5242: Microcontroller Replacement for MC9S08GB60ACFUE

    TI Thinks Resolved
    Part Number: MSP430F5242 Hello, I'm working on a part cross for a customer system and wondering if there are any recommended MSP430 devices to replace a MC9S08GB60A MCU. The closest cross I was able to find was the MSP430F524x line with similar Flash…

  • CCS/MSP430F5242: MSP430 PMBus Slave implementation

    TI Thinks Resolved
    Part Number: MSP430F5242 Tool/software: Code Composer Studio Hi all, the PMBus master implementation code is available for the MSP430 but not for the slave. In my application the MSP430 would act as a PMBus slave. Is some library or application note exist…
    • Answered

  • MSP430F5242: DCO accuracy at 24MHz

    Resolved
    Part Number: MSP430F5242 Hi Team, Could you kindly advise the accuracy of DCO at DCO=24MHz ? Customer find the 0.1%/ degree in the datasheet though.. They need to communicate at over 900kbps, so they are concerned about missing the data caused by accuracy…
    • Resolved
    • Answered

  • RTOS/MSP430F5242: Recommended Evaluation Platform

    Resolved
    Part Number: MSP430F5242 Other Parts Discussed in Thread: MSP-EXP430F5529LP , MSP-TS430RGC64C , MSP-FET , MSP-EXP430FR5969 , MSP430F5249 Tool/software: TI-RTOS Hi Team, My customer is planning to use the MSP430F5242. There does not seem to be an eval board…
    • Resolved
    • Answered

  • MSP430F5242: I2C Driverlib, repeated start condition

    Resolved
    Part Number: MSP430F5242 Hello! I was trying to switch to the USCI_B I2C Driverlib and i noticed i couldn't reproduce a clean repeated start condition (e.g. for reading a byte from the slave). If i watch the waveforms with the oscilloscope i can see the…
    • Resolved
    • Answered

  • MSP430F5242: PIN FEMA test report available based on IEC61508?

    Resolved
    Part Number: MSP430F5242 Dear TI Experts, My customer wants to know if PIN FEMA test report is available based on IEC61508, for instace, what will happen if each PIN short to GND/VCC, short to adjacent PIN and so on. Thanks a lot.
    • Resolved
    • Answered

  • MSP430F5242: total current under Reduced Drive Strength

    Resolved
    Part Number: MSP430F5242 Hello Champs, In F5242 datasheet Chapter 5.11, there is description for two conditions in note (2) and note (3): Customer needed to know when they should refer to note (2) conditions(48mA) and when they should refer to note (3…
    • Resolved

Didn't find what you are looking for? Post a new question.