Search tips
Showing 57 results View by: Thread Post Sort by

  • MSP430F6733: challenging The MSPBoot application report (slaa600a)

    Part Number: MSP430F6733 Hello We consider a bootloader implementation based on the MSPBoot slaa600a application report, in one of our MSP430F6733 based products. One of our senior engineers was challenging the boot force mechanism (option 2) It says in…
    • Answered

  • MSP430F6733: Is it necessary to clear the interrupt flag(s) before entering LPM4 ?

    Resolved
    Part Number: MSP430F6733 Hello, Is it necessary to clear the interrupt flag(s) before entering LPM4 ? (Necessary / preferable / not necessary ?) Our question above is an important point of customer's logic, so please reply whatever your advice to the background…
    • Resolved
    • Answered

  • msp430f6733: UNused UART pins

    Resolved
    Hello, I tried to list the configurations of UNused UART pins. Could you please check ? - The wiring is OPEN. - The F/W to set the pin function as GPIO . - The F/W to set the direction to OUTPUT. - The output state (H/L) ---- Need your advice . History…
    • Resolved

  • MSP430F6733 SD24 setting

    TI Thinks Resolved
    Hi I am using SD24 with setting register below. SD24BCCTLx[8bit] = 0b continuous mode SD24BOSRx[0-9bit] = FFh (OSR=255) SD24INTDLYx[6-7bit] = 11b First sample causes interrupt But I couldn't get any sample. (When I check the sample value , all sample…

  • MSP430F6733 sinc3 filter

    Other Parts Discussed in Thread: MSP430F6733 Hello I read something about a sinc3 filter, and there are some information. But I can't understand its characteristics. I understand a sinc3 filter is some kind of simple moving average. Is it wrong? If…

  • MSP430F6733 SD24INTDLYx SD24SNGL setting

    TI Thinks Resolved
    Hi If I use SD24INTDLYx as 00b and SD24SNGL as 1b, what I get sample is below, right? Input signal is PWM wave.
    • Answered

  • msp430F6733: How to demonstrate ILPM4=1.6uA ? (Schem and Firmware)

    Resolved
    Other Parts Discussed in Thread: ENERGYTRACE , MSP-FET , EVM430-F6736 Hello, Could you please advice how to demonstrate ILPM4=1.6uA ? Let me explain my status: - I built a board as the attached schem - The sample code "MSP430F673X_LPM4.c" was executed.…
    • Resolved

  • Input-referred noise of MSP430F6733 SD24(PGA).

    Other Parts Discussed in Thread: MSP430F6733 , ADS1191 , ADS1192 , ADS1263 Hello. Do you have Input-referred noise specification of SD24_B of MSP430F6733. I know that there is a value of SINAD of SD24_B in the data sheet of MSP430F6733. However, he is…

  • msp430f6733: Setting the P1.4 as UART_RxD, and the same time enabling the pull-up

    Answer Suggested
    Other Parts Discussed in Thread: MSP430F2416 Hello, Is it possible to set the P1.4 as UART_RxD, and the same time pull-up enabled ? Updated question: Is it possible to set the P1.4 as UART_RxD, and the same time enable the pull-up ? Best regards, -n …
    • Answered

  • The target setup (MSP430F6733) does not match the actual target type (MSP430F6723)

    Resolved
    Other Parts Discussed in Thread: MSP430F6723 , MSP430F6733 Hi i am ugra, Every time i debug my program in code composer studio v5 it gave me the following error: Error connecting to the target: the target setup (MSP430F6733) does not match the actual target…
    • Resolved

Didn't find what you are looking for? Post a new question.