Search tips
Showing 17 results View by: Thread Post Sort by
    Answered

  • MSP430G2313: The comparator will not work after watchdog reset

    Resolved
    Part Number: MSP430G2313 Hi Team, Here's an issue from the customer may need your help: When working normally, the comparator outputs a square wave. The watchdog will reset the MCU after 1 second if the comparator output does not change. Use an oscilloscope…
    • Resolved

  • MSP430G2313: BSL issue

    TI Thinks Resolved
    Part Number: MSP430G2313 Issue: Failed to read data from 0x0f00 bit According to the manual, enter the BLS state, send 80 to the monolithic, and receive 90 responses normally. Sending 80 14 04 04 00 0F 0E 00 75 E0 again returns a 0xA0 answer and does…

  • MSP430G2313: BSL password error issue

    Part Number: MSP430G2313 Hi team, The left figure above shows the end of the txt burn file, and the right figure is a manual BSL password. The BSL Downloader always shows a password error, the customer would like to know the correct password. Could…

  • MSP430G2313: The burn in program runs normally. After working for a period of time, the program does not run, and it does not run when powered on again! Run after re burning

    Part Number: MSP430G2313 I have made five products, one of which runs normally. After working for a period of time, the program does not run, and it does not run when powered on again! Run after re burning. Time0 uses the internal 16m clock to send PWM…

  • MSP430G2313: MCU of ADC compiles issue

    TI Thinks Resolved
    Part Number: MSP430G2313 Dear team, My customer used the TI software Code Composer Studio 9, did the TI of ADC sample code(msp430g2x33_adc10_01.c) compiles on the MSP430G2313 chip, then they found happened many error and came from the chip default parameter…
    • Answered

  • MSP430G2313: Genereting 1MHz pulses via SPI - UxBR register

    Resolved
    Part Number: MSP430G2313 Hi team, my customer wants to use SPI to generate a chain of 8 pulses with 1MHz (send one byte via SPI). They intend to use the DCO set to 1MHz and configure UxBR to '1' (divide by 1) to get SPI speed of 1MHz. However,…
    • Resolved

  • MSP430G2313: MSP430 USCI SPI slave recv seems to be off by one bit.

    Part Number: MSP430G2313 Greetings I am configuring my MSP430G2313 USCI as an SPI slave (POL=0, PH=0, 3-Wire, RX interrupt enabled) that is connected to an SPI master via a detachable connector. When I attach the connector, there is the possibility of…

  • MSP-GANG programmer error

    Other Parts Discussed in Thread: MSP430G2313 , MSP430F5419A , MSP430G2553 , MSP-GANG Hi, There is error message which I captured when I connecct the programmer with PC using USB cable. Have a look at the “Programmer’s Internal Image Memory”. There are a few…
    • Answered

  • LED/LCD 3 Digit - 7 segment Display Driver

    Resolved
    Other Parts Discussed in Thread: MSP430G2313 , TCA6507 , MSP430G2452 , LP2951 , SN74AHC595 , TLC6C598 I am looking at using an MSP430G2313 Value Line uC + LCD or LED driver (I2C or SPI). For example, the display I am looking at is a ChromeLED P/N: SDTA28R2…
    • Resolved
    • Answered

  • msp430g2553 clock calibration header values

    Resolved
    Other Parts Discussed in Thread: MSP430G2553 , MSP430G2153 , MSP430G2203 , MSP430G2213 , MSP430G2233 , MSP430G2253 , MSP430G2303 , MSP430G2313 , MSP430G2333 , MSP430G2353 , MSP430G2403 , MSP430G2413 , MSP430G2433 , MSP430G2453 , MSP430G2513 , MSP430G2533 , MSP430TCH…
    • Resolved

Didn't find what you are looking for? Post a new question.