• 

  Jim Grimes

  • 1 day ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

  MSP430G2553: Clocking options to achieve acceptable error at standard UART baud rates

  Part Number: MSP430G2553 In trying to assure error free communication at 115200 baud for the USCI (UART mode), its not clear on options for clocking this device. We also need help in interpretation of UG table 15-4 and 15-5 The DCO table (pg 30 of the...
• 

  Srinivas Lingam

  • 9 days ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

  RE: MSP430G2553: Controlling neopixel led using Msp430G22553

  Hi Hakan, I think the showStrip() sends out the RGB values for each LED in the outer for loop:: for (i = 0; i < NUM_LEDS; i++) { In the 2nd for loop, as the comments indicate, it sends out the value corresponding to green, then red, then blue:...
• 

  Tomas Roubicek

  • 12 days ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

  RE: CCS/MSP430G2553: after uart interrupt next function not running

  Hello. You have to add intrinsic function __bic_SR_register_on_exit(LPM0_bits); into the ISR to prevent switching to LPM after exit. Best regards, Tomas
• 

  ASHRITH RAMESH

  • 1 month ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

  MSP430G2553: SCHMITT_trigger

  • Resolved

  Part Number: MSP430G2553 Hi, I have obtained the above screen shot from MSP4302553 DataSheet. I am
• 

  Keith Barkley

  • 18 days ago
  • Code Composer Studio™
  • Code Composer Studio™ forum

  RE: Compiler/MSP430G2553: CCS Terminal Window for Serial Communication

  Time to get the scope out and see if the issue is on the tx or rx side. You can also set the LED on the board to toggle for every character received/transmitted.
• 

  Gilberto Zamarron

  • 20 days ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

  RE: CCS/MSP430G2553: potential issue configuring i/o with a pull down resistor for port 6?

  Thank you! I tried what you mentioned at it solved my issue.
• 

  Susan Yang

  • 1 month ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

  MSP430G2553: TI_measureVLO() affects the initialization of static variables

  TI Thinks Resolved

  Part Number: MSP430G2553 Dear team, I am using IAR 7.4 with MSP430G2553. I found that TI_measureVLO() affected the initialization of static variables. static unsigned char rxBitCnt= 8; when i do NOT use TI_measureVLO. But it was 49 when i used...
• 

  Winter Yu

  • 1 month ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

  RE: MSP430G2553: Run blink led demo on breadboard with msp430g2553

  Hello, 1. 3.3V power supply with 0.1uF and 10uF decoupling capcitor. 2. SBW program and debug interface 3. LED with resistor connected
• 

  ASHRITH RAMESH

  • 2 months ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

  MSP430G2553: MSP430G2553: ADC Configuration issue

  • Resolved

  Part Number: MSP430G2553 Hi, I have referred to the sample programs to configure msp430g2553 ADC10
• 

  Bruce McKenney47378

  • 1 month ago
  • MSP low-power microcontrollers
  • MSP low-power microcontroller forum

  RE: CCS/MSP430G2553: Configuring GPIO pin functions (PxSEL & PxSEL2)

  This information isn't in the user guide (SLAU144J), but rather in data sheet (SLAS735J) Table 16. That indicates that the pin usage is configured by multiple settings, not just the P1SEL bits. For your case you want DIR=1, SEL=1, SEL2=0. [CAPD...

Didn't find what you are looking for? Post a new question.

• Ask a new question