Search tips
Showing 113 results View by: Thread Post Sort by
    Answered

  • MSP430G2755: How to filter noise input to analog input of MCU?

    Resolved
    Part Number: MSP430G2755 Other Parts Discussed in Thread: OPA344 Tool/software: Hi Experts, We'd like to ask assistance if there is any way to calculate what cut off frequency needed on this circuit: With scope shot: Without MCU (red graph…
    • Resolved
    • Answered

  • MSP430G2755: give the step-by-step procedure to use MSP430G2755 with ARDUINO IDE or ENERGIA platform. If it is not possible, please describe the usage in CCS.

    Resolved
    Part Number: MSP430G2755 Other Parts Discussed in Thread: ENERGIA , , MSP-EXP430G2ET Please give the step-by-step procedure to use MSP430G2755 with ARDUINO IDE or ENERGIA platform. If it is not possible, please describe the usage in CCS. Thank You,…
    • Resolved
    • Answered

  • MSP430G2755: Issue when moving/changing start address using linker command file

    Resolved
    Part Number: MSP430G2755 Our project has a customer bootloader. * The FLASH is partitioned to support both the bootloader and application. -- The bootloader starts at 0xE000. The bootloader and FLASH vectors are fixed -- The application starts at 0x8000…
    • Resolved

  • MSP430G2755: Question about MSP430G2755IRHA40R

    Part Number: MSP430G2755 hello: The customer's smart gas meter project has imported MSP430G2755IRHA40R, a project that has been mass-produced in 21 years. See the attachment for the specific schematic diagram At present, it has been used by end customers…
    • Answered

  • MSP430G2755: Data Verification Error Occured

    Resolved
    Part Number: MSP430G2755 Other Parts Discussed in Thread: MSP-FET , , MSP430G2744 I use the TI's MSP430G2755 Microcontroller. I used 4 PWM signals with two timer modules. I uploaded the code to the microcontroller using the TI MSP-FET Flash Emulation…
    • Resolved

  • MSP430G2755: BSL Memory Type

    TI Thinks Resolved
    Part Number: MSP430G2755 Hello, The MSP430G2755 datasheet indicates that the BSL memory is flash based: But the MSP BSL App note indicates that it should be ROM based: Which is it?

  • MSP430G2755: Discrepancy in SRAM value

    Part Number: MSP430G2755 Hi, Can you help me understand why the MSP430G2755IRHA40R product page shows 2KB of SRAM: While the datasheet shows 4KB of SRAM:
    • Answered

  • MSP430G2755: Is it possible to setup the UART to inverted signal lines (nonactive low)

    Resolved
    Part Number: MSP430G2755 HI, I just wanted to know if it is possible to invert the UART lines (non active low)? Kind regards Christian
    • Resolved

  • MSP430G2755: Question about MSP430G2755IRHA40R

    TI Thinks Resolved
    Part Number: MSP430G2755 Hello： The main chip is msp430g2755irha40r. The motherboard was successfully burned in before, and the following bad prompt will appear when the program burns in again. Please check it，Thanks！ 2-wire burn in
    • Answered

  • MSP430G2755: SPI configuration

    Resolved
    Part Number: MSP430G2755 Hi Team, We would like to ask your help regarding our customer's inquiry below. Hello, I am trying to configure the MSP430G2755 to communicate via that spi bus to a TPL0501 (digital resistor). I have pin 10, P3.1 set as…
    • Resolved

Didn't find what you are looking for? Post a new question.