Search tips
Showing 114 results View by: Thread Post Sort by
    Answered

  • MSP430G2755: SPI configuration

    Resolved
    Part Number: MSP430G2755 Hi Team, We would like to ask your help regarding our customer's inquiry below. Hello, I am trying to configure the MSP430G2755 to communicate via that spi bus to a TPL0501 (digital resistor). I have pin 10, P3.1 set as…
    • Resolved

  • MSP430G2755: Failure to run the program after 10 seconds the MCU was powered

    Part Number: MSP430G2755 Dear Team, Hope you are doing well. I got a question from the customer during the use of MSP430G2755. They found that some G2755 malfunctioned: 1.Less than 10 seconds after powered G2755, the G2755 was failed to run the…

  • MSP430G2755: Voltage rise slope when power is applied to DVCC

    Part Number: MSP430G2755 Hi, I checked the data sheet, but there was no information on the DVCC rise time constraint (~ ○○ V / S). Do you have any information about that? Thanks, Koki
    • Answered

  • MSP430G2755: Spy-Bi-Wire and JTAG

    Resolved
    Part Number: MSP430G2755 Other Parts Discussed in Thread: MSP430G2553 , MSP-FET HI, Please help to confirm, thank you. 1. Does it support MSP430G2553 LaunchPad Board connection to use Spy-Bi-Wire (SBW)? See application report SLAA754. 2. Does it support…
    • Resolved
    • Answered

  • MSP430G2755: Debugging and programming the device with the eZ-FET Emulator by 1.8V Supply

    Resolved
    Part Number: MSP430G2755 Other Parts Discussed in Thread: MSP430FR2311 , MSP-FET Hi dear people, my custom board with a MSP430G2755 should work with a supply of 1.8V. Debugging and programming the device with the eZ-FET Emulator from the MSP430FR2311…
    • Resolved
    • Answered

  • MSP430G2955: moving from MSP430G2755 to MSP430G2955 since p2p will just recompile

    Resolved
    Part Number: MSP430G2955 Hi, if I move from 2755 to 2955 i see only thing that changes is the flash, just want to check can i just recompile code from 2755 on 2955 and if wasn't havn't issues before it should just recompile the same? Thanks
    • Resolved

  • RE: MSP430G2755: Sigfox on MSP430G2755

    Anders, The Sigfox SDK is very dependent on the exact processing speed of the MCU that is executing the code. We have only ported the SDK to the 5529 and we found that when running the 5529 at 16MHz we had trouble passing the Sigfox mask. Therefore…

  • MSP-GANG: Error 23 occurs while using the MSP430G2755

    TI Thinks Resolved
    Part Number: MSP-GANG Other Parts Discussed in Thread: MSP430G2755 Hi experts, My customer created a board using the MSP430G2755, but it has been unable to write on some boards since an error 23 was displayed. The customer thinks that the IC has failed…
    • Answered

  • MSP430G2755: Correct D1 and D2 values to change BSL UART baud rate to 38400

    Resolved
    Part Number: MSP430G2755 I'm writing an internal tool for reprogramming the MSP430G2755 on our device using BSL. I can do this but it takes quite a while at 9600 baud, so I'd like to increase the baud rate. The app note doesn't give a lot of background…
    • Resolved

  • MSP430G2755: Microcontroller works in debugger mode, but turning it on without MSP-EFT does not work.

    Part Number: MSP430G2755 Other Parts Discussed in Thread: MSP-FET , Greetings to the entire community. I am doing a development for my company of telemetry devices, but I have a problem now that I finish the code, when connecting the MSP-FET to the…

Didn't find what you are looking for? Post a new question.