• OMAP3530: OMAP3530 Boot loader??

  

  kevin wang1

  TI Thinks Resolved

  Part Number: OMAP3530 Hi, I am working on a board using OMAP3530. I have a question about the booting sequence. Do I need to create a boot loader? If so, how? and where do I need to put? If not, where I can put the initial mode settings for the pins…

  • 1 day ago
  • Processors
  • Processors forum
Answered

• OMAP3530: OMAP3530: UART - How long it takes to clear TX/RX FIFO?

  

  pxshu

  Resolved

  Part Number: OMAP3530 Hi All, Sorry to bother again - our product is now using this processor for mass production and it cannot be replaced/upgraded easily... In OMAP35x technical reference manual, Table 17.54 said FCR_REG.TX_FIFO_CLEAR is a write-only…

  • Resolved

  • 29 days ago
  • Processors
  • Processors forum
Answered

• OMAP3530: OMAP3530: UART - How long it takes to switch from oper mode to config mode A/B and vise versa?

  

  pxshu

  Resolved

  Part Number: OMAP3530 Hi, Does anyone know how long will OMAP3530 take to switch UART mode from operational mode to configuration mode A/B and vise versa? Say it'll be switch to new mode within xxx milliseconds? I don't find it in technical reference manual…

  • Resolved

  • 1 month ago
  • Processors
  • Processors forum

• OMAP3530: OMAP3530 & TPS65950 questions

  

  kevin wang1

  Part Number: OMAP3530 Other Parts Discussed in Thread: TPS65950 , I have some questions between OMAP3530 and TPS65950. I connected I2C1 of OMAP3530 to I2C_CNTL of TPS65950 and I2C4 of OMAP3530 to I2C_SR of TPS65950 1. ADC: 1a. I am using ADCIN2 and ADCIN5…

  • 3 months ago
  • Processors
  • Processors forum
Answered

• OMAP3530: OMAP3530 & LPDDR RAM MT46H64M32LFBQ-48

  

  kevin wang1

  Resolved

  Part Number: OMAP3530 I am going to use LPDDR RAM on OMAP3530. Do I need to put the pull-high resistor on the address line or other pin? If so, what's the value? Thanks.

  • Resolved

  • 3 months ago
  • Processors
  • Processors forum

• OMAP3530: NAND Flash usage issues

  

  Qiqin Ouyang

  TI Thinks Resolved

  Part Number: OMAP3530 The chip I am using is OMAP3530，and the nand flash is TH58NYG3S0HBAI4 . The nand flash datasheet said, 8 bit ECC for each 512Byte is required. Omap RootRom only complete 1bit correction. How can I get omap to use this nand chip…

  • 20 days ago
  • Processors
  • Processors forum

• OMAP3530: available memory Ram and Flash for OMAP3530

  

  kevin wang1

  Part Number: OMAP3530 Other Parts Discussed in Thread: AM3715 Hi all, I am doing a new design using OMAP3530. I don't want to put POP memory need to separate Ram and NAND flash. Which available RAM and NAND FLASH I can use in my design? Thanks.

  • 4 months ago
  • Processors
  • Processors forum

• OMAP3530-HIREL: Temperature Code clarification

  

  Art Mecina

  TI Thinks Resolved

  Part Number: OMAP3530-HIREL Hello Guys, Good day. Just like to clarify. On page 256 under device nomenclature of the device it was stated that the 'A' suffix means it is rated at -40° C to 105° C. However, on the Packaging information on page 258, all…

  • 2 months ago
  • Processors
  • Processors forum

• OMAP3530: OMAP3530

  

  kevin wang1

  Part Number: OMAP3530 Hello, I am going to use OMAP3530 in my new design. Where can I find a reference design (schematics)? I need to know about the memory parts, RAM, NAND FLASH.... Thanks,

  • 7 months ago
  • Processors
  • Processors forum
Answered

• OMAP3530: OMAP3530

  

  Terry Dmytruk

  Resolved

  Part Number: OMAP3530 Is it possible to identify which version of OMAP3530 from the ID registers. Specifically: Is it an extended temperature or standard commercial device. Thank you Terry Dmytruk

  • Resolved

  • 9 months ago
  • Processors
  • Processors forum

Didn't find what you are looking for? Post a new question.