Answered

• SN54LVC14A-SP: TID Rating of SN54LVC14A-SP

  

  Scott Hill

  Resolved

  Part Number: SN54LVC14A-SP Other Parts Discussed in Thread: SN54AC14-SP , SN54SC6T14-SEP Hi, I am looking into using PN: SN54LVC14A-SP for a project with a 30krad TID requirement. The datasheet does not list a TID even though it is a -SP part. What is…

  • Resolved

  • 1 month ago
  • Logic
  • Logic forum
Answered

• SN54LVC14A-SP: 2.5V level translator

  

  Robert

  Resolved

  Part Number: SN54LVC14A-SP Other Parts Discussed in Thread: SN54AC14-SP , SN54HC14-SP , Hello, I have a 2.5V device that needs to communicate with a 3.3V system. I plan on using the SN54LVC14A-SP to translate the 3.3V signals down to 2.5V, and I'm wondering…

  • Resolved

  • 1 month ago
  • Logic
  • Logic forum
Answered

• SN54LVC14A-SP: Missing Footprint

  

  Kyle Cerniglia

  Resolved

  Part Number: SN54LVC14A-SP We urgently need the footprint for the LCCC(FK) package of this part. The footprint documentation you provide only has a 3D render of the package, there are no drawings of body dimensions or footprint layout. Thanks

  • Resolved

  • 3 months ago
  • Logic
  • Logic forum
Answered

• SN54LVC14A: SN54LVC14A Vin question check

  

  Bo Xian Yeh

  Resolved

  Part Number: SN54LVC14A Tool/software: Hi Team, My customer have a case where the voltage signal will have undershoot to close to -1V Check SN54LVC14A datasheet that the minimum Vin for the SN54LVC14A is -0.5V. Is there further reserved safety values…

  • Resolved

  • over 2 years ago
  • Logic
  • Logic forum
Answered

• SN54LVC14A: Radiation SEL LET question

  

  CHO SR

  Resolved

  Part Number: SN54LVC14A Hi, The customer needs SELET information. TID information is written on the data sheet, so you can check it. However, there is no SEL LET information, so I request the information.

  • Resolved

  • over 2 years ago
  • Logic
  • Logic forum

• SN54LVC14A-SP: how to connect NC pins

  

  Joey Christ

  TI Thinks Resolved

  Part Number: SN54LVC14A-SP I have a system level requirement that no pins can be left floating. Can the following NC pins be connected to GND without changing the behavior of the part?

  • over 2 years ago
  • Logic
  • Logic forum
Answered

• SN54LVC14A: Are the terminals gold plated

  

  Amy Luo

  Resolved

  Part Number: SN54LVC14A Hi team, In the old version of SN54LVC14AFK datasheet, it was clearly stated that the pins were gold-plated, as shown in the figure below. But the latest datasheet does not have this sentence, so please make sure that the pin…

  • Resolved

  • over 5 years ago
  • Logic
  • Logic forum
Answered

• SN74LVC14A: Input rise/fall time spec

  

  Kazuhiko Hirano

  Resolved

  Part Number: SN74LVC14A Other Parts Discussed in Thread: SN54LVC14A , Hello, Datasheet 8.3.2 states as follows and it confused me a lot. “Signals applied to the inputs need to have fast edge rates, as defined by Δt/Δv in Recommended Operating Conditions…

  • Resolved

  • over 4 years ago
  • Logic
  • Logic forum

• SN74LVC14A: Enquire on radiation data

  

  Nick Cheng

  TI Thinks Resolved

  Part Number: SN74LVC14A Other Parts Discussed in Thread: SN54LVC14A , SN54LVC14A-SP Dear Sir/Madam, I'm interested in SN74LVC14A in term of it's VCC operation of 1.65-V to 3.6-V. I'm looking if there is radiation tests been performed on SN74LVC14A?…

  • over 9 years ago
  • Logic
  • Logic forum
Answered

• RE: SN54LVCH244A-SP: balanced outputs and bus hold

  

  Clemens Ladisch

  Resolved

  All CMOS devices allow their outputs to be paralleled; see [FAQ] Can I connect two outputs from a CMOS logic device together directly? You can use bus-hold inputs in parallel if the other device has enough drive strength. If in doubt, put another buffer…

  • over 3 years ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.