• SN65EPT21: SN65EPT21 Temperature Compensation

  

  Nathan Baltz

  TI Thinks Resolved

  Part Number: SN65EPT21 Tool/software: Hi, The SN65EPT21 (PECL/LVDS differential in TTL out) says its temperature compensated. Does anyone have any data on the Temperature Coefficient of propagation delay of this part? Can this part handle ultra low duty…

  • 3 months ago
  • Interface
  • Interface forum

• SN65EPT21: Definition of VIH, VIL, VIHCMR and VPP

  

  Hung Ching Hsu

  TI Thinks Resolved

  Part Number: SN65EPT21 Hi Team, My customer have following questions about SN65EPT21. Could you kindly help? Thanks. 1. Definition of VIH and VIL. Does it mean if D and D bar pin have input signal ranging 2075mV~2420mV, it will be seen HIGH inside IC.…

  • over 3 years ago
  • Interface
  • Interface forum
Answered

• SN65EPT21: duty cycle in terms of percent?

  

  Michael T Schneider

  Resolved

  Part Number: SN65EPT21 Team, For the SN65EPT21D, is there a specification for duty cycle in terms of percent? The data sheet shows duty cycle skew only? customer is asking

  • Resolved

  • over 4 years ago
  • Interface
  • Interface forum

• SN65EPT21: DC-coupled for a LVDS input

  

  weigang Fu

  TI Thinks Resolved

  Part Number: SN65EPT21 Other Parts Discussed in Thread: SN65LVDS348 Hi, I'm looking for a 1-to-1 Differential-to-LVCMOS/LVTTL Translator, the differential signal is a 8K LVDS clock, I see a AC-coupling application report on TI network, but AC-coupled…

  • over 4 years ago
  • Interface
  • Interface forum

• SN74LVC1T45: SN74LVC1T45

  

  Chuanfu Liu

  TI Thinks Resolved

  Part Number: SN74LVC1T45 Other Parts Discussed in Thread: TXV0106 , SN65EPT21 , SN65EPT23 Tool/software: Hi TI team I am looking for a low latency tPLH/tPHL and low part skew 1.5V to 3.3V or 2.5V level translation chip. expecting tPLH <2 ns, tPLH part…

  • 4 months ago
  • Logic
  • Logic forum
Answered

• SN65EPT21: Input and output voltage level mismatch

  

  Srikanth Kacchu1

  Resolved

  Part Number: SN65EPT21 Hi I am planning to use SN65EPT21DGK for PECL to TTL conversion. But the datasheet spec confused me. Title of the datasheet says it is PECL to TTL but the package and pin function table shows LVPECL to LVTTL. Also, electrical characteristics…

  • Resolved

  • over 5 years ago
  • Interface
  • Interface forum

• RE: TLV3801: Regarding single ended output application

  

  Clemens Ladisch

  You can either use a comparator with push/pull output like the TLV3601, or add an LVDS receiver like the SN65EPT21. Both are much slower. And the SPDT switch will have an additional delay.

  • 8 months ago
  • Amplifiers
  • Amplifiers forum
Answered

• SN65EPT21: LVPECL(Single-ended) to TTL translation application

  

  Koshi Ninomiya

  Resolved

  Part Number: SN65EPT21 Other Parts Discussed in Thread: SN65LVDS100 Hi Team, I am going to use SN65EPT21 for LVPECL (Single-ended) to TTL application. Could you review my application circuit below? SN65EPT21 application.xlsx If there are anything which…

  • Resolved

  • over 5 years ago
  • Interface
  • Interface forum

• SN65EPT21: RS485 to optical fiber media converter

  

  suvra mukherjee

  TI Thinks Resolved

  Part Number: SN65EPT21 Other Parts Discussed in Thread: SN65LVELT22 I want to make Rs485 to optical fiber media converter. Please confirm me whether these parts are suitable to make the converter or not. Please suggest me. 7607.RS485 to optical.pptx

  • over 6 years ago
  • Interface
  • Interface forum
Answered

• SN65EPT21: CML to TTL/CMOS translation

  

  Juergen Schneider

  Resolved

  Part Number: SN65EPT21 Hi, I planned to apply the circuit SN65EPT21 ( supported by +3.3V) to translate a differential CML- Signal ( CML- Driver is supported by +2.5V) to a single- ended TTL/ CMOS- Signal. What kind of termination is there required ( D…

  • Resolved

  • over 7 years ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.