Search tips
Showing 71 results View by: Thread Post Sort by

  • SN65HVD10: Request for Information on Short/Open Behavior for SN65HVD10

    TI Thinks Resolved
    Part Number: SN65HVD10 Tool/software: Hi, We are conducting an internal Failure Mode and Effects Analysis (FMEA) for our products and require specific information regarding the behavior of the following TI ICs under short and open conditions: Target…
    • Answered

  • SN65HVD10: SCH&Layout review

    Resolved
    Part Number: SN65HVD10 Tool/software: Hi Team, Can you help to review below sch and layout? Thanks! There will be 3 solutions applied in one project. RS485layout revieww.pptx
    • Resolved

  • SN65HVD10: what is the difference between the "13M" and "15M" markings on the SN65HVD10 device.

    TI Thinks Resolved
    Part Number: SN65HVD10 Tool/software: Hi TI Team, We've encountered communication issues between two FPGA boards using SN65HVD10 transceivers. Specifically, we observed communication breaks when using devices marked "13M. " However, replacing them with…

  • SN65HVD10: Auto-grade, UART to RS485 (3.3V level)

    TI Thinks Resolved
    Part Number: SN65HVD10 Other Parts Discussed in Thread: SN65HVD1780-Q1 , THVD1450 , THVD1406 Tool/software: Hi Team, As title, do we have solution that meet auto-grade, UART to RS485 (3.3V level) feature? Regards, Roy
    • Answered

  • SN65HVD10: input voltage with unbiased device?

    Resolved
    Part Number: SN65HVD10 Tool/software: According to max abs rates for this part, voltage at A and B terminals can be -9 to 14V Does this include the chip being unpowered?
    • Resolved
    • Answered

  • SN65HVD10: What kind of performance degradation can be expected if the driver output current remains at or slightly exceeds 60 mA?

    Resolved
    Part Number: SN65HVD10 Tool/software: One of our 485 network designs has baselined termination resistors at every node as opposed to a single 100ohm termination at the end of the trunk. This causes increased current at the driver which we are currently…
    • Resolved

  • SN65HVD10: SN65HDV1781DR

    Part Number: SN65HVD10 Other Parts Discussed in Thread: THVD2410 Hi we have RS485 support VCC=3.3V with internal charge pump so Voh can be 4.7V as VCC=5V spec? Thank you!
    • Answered

  • SN65HVD10-EP: Maximum current consumption

    Resolved
    Part Number: SN65HVD10-EP Tool/software: Hello, I would like to know the max current consumption of RS-485 TRANSCEIVERS for using in our power supply If power supply 3.3V 50mA, it that enough? Could you pls send me the suggestion? Best Regards,…
    • Resolved

  • SN65HVD10: SN65HVD10 isolation between two modules

    TI Thinks Resolved
    Part Number: SN65HVD10 Other Parts Discussed in Thread: ISOW1432 , ISO1430 , ISO1450 Hi Team, We used the transceiver (SN65HVD10DR). I've included the circuit diagram below. The issue was that we had connected the SN65HVD10DR to the B&R CS communication…
    • Answered

  • SN65HVD10: Temperature ratings of Q and non-Q version

    Resolved
    Part Number: SN65HVD10 Tool/software: I was wondering if I could get more details on the difference between the Q and non-Q part number of the SN65HVD10? Why is the Q Ta rated to 125C vs the non-Q only rated to 85C? The recommended operating conditions…
    • Resolved

Didn't find what you are looking for? Post a new question.