Search tips
Showing 16 results View by: Thread Post Sort by

  • SN65HVD1176: Power dissipated by the driver used with a long cable

    TI Thinks Resolved
    Part Number: SN65HVD1176 Hello, I would like to evaluate the dissipated power by the driver over a long cable (1km). Using this link https://e2e.ti.com/blogs_/b/analogwire/posts/how-to-calculate-the-power-dissipation-of-high-speed-rs-485-transceivers ,…

  • SN65HVD1176: Part-to-Part propagation time variance

    Part Number: SN65HVD1176 Assuming the exact same input was driving infinite SN65HVD1176 RS-485 transceivers, and the single-ended input went from 0 to 3.3v, if measuring the output of each driver on a scope what would be the maximum time between the first…
    • Answered

  • SN65HVD1176: Differences SN65HVD1176D vs SN65ALS1176D

    Resolved
    Part Number: SN65HVD1176 Hello, can SN65ALS1176D be considered a direct replacement for SN65HVD1176D? Many thanks, Alessio
    • Resolved
    • Answered

  • SN65HVD1176: Pull-up resistor on Received Data (R) pin

    Resolved
    Part Number: SN65HVD1176 Other Parts Discussed in Thread: PROFIBUS , ISO7721 Hello, I'm designing an isolated PROFIBUS interface, and I would like to use the transceiver SN65HVD1176 + other external optocouplers (for example, ISO7721 for TX and RX on logic…
    • Resolved

  • SN65HVD1176: Bias resistors and termination resistors values calculation in the dual fail-safe biasing application

    Part Number: SN65HVD1176 Other Parts Discussed in Thread: PROFIBUS , Hi All, I have a questions for bias resistors and termination resistors calcultions. The Profibus cable Impedance is 150R (type: 6XV1830-0EH10 ) and power is 5Vdc isolation. As learn datasheet…
    • Answered

  • SN65HVD1176: Part is Destroyed when Switching from 0V to -7V on Terminal A

    Resolved
    Part Number: SN65HVD1176 Hello, I'm trying to do the "Input voltage ranges" test specified in TIA-485-A. Therefore, I have to apply -7V to terminal A and -6.8V to terminal B of the transceiver (see Table 1 in section 4.3.2 of the standard). During the…
    • Resolved

  • SN65HVD1176: Device spacing on RS-485 buses

    Part Number: SN65HVD1176 We are looking for a bus solution for up to 300 nodes were the nodes are mounted relatively close to each other (spacing 5cm). While reading the 'Device spacing on RS-485 buses' Analog Applications Journal ( http://www.ti…
    • Answered

  • SN65HVD1176: Differential output voltage

    Resolved
    Part Number: SN65HVD1176 Other Parts Discussed in Thread: SN65HVD50 , SN65HVD05 , PROFIBUS Does TI have a driver with a higher minimum Differential Output Voltage than the SN65HVD1176? Something like 2.4V – 3V into 54 Ohms? The data rate isn’t as…
    • Resolved
    • Answered

  • THVD1450: Profibus standard

    Resolved
    Part Number: THVD1450 Other Parts Discussed in Thread: SN65HVD1176 , PROFIBUS , Hello Both SN65HVD1176 and THVD1450 datasheets says they support profibus. Does it mean both devices comply IEC61158-2 Profibus standard and Profibus certification test specification…
    • Resolved

  • THVD1450: Differential input capacitance of THVD1450 and THVD2450

    Part Number: THVD1450 Other Parts Discussed in Thread: SN65HVD1176 , THVD2450 , Hi team, My customer wants to transfer from SN65HVD1176 to THVD1450/THVD2450, but find there is no data for differential input capacitance. Can I know what is the differential…

Didn't find what you are looking for? Post a new question.