• SN65HVD1473: RS-422 terminaison resistor

  

  Megane TREMBLIER

  Part Number: SN65HVD1473 Hi there, I'm using the SN65HVD1473 transceiver in RS-422 mode. As the data rate is over 200 Kbps we need a 120ohm terminaison resistor. What reference do you advise to use? Which package? In fact, the EIA-422 indicates a maximum…

  • 4 months ago
  • Interface
  • Interface forum

• SN65HVD1473: Using SN65HVD1473 to switch between half and full duplex

  

  Christina Lim

  TI Thinks Resolved

  Part Number: SN65HVD1473 HI All, I had a customer whom is interested to implement similar switch betwee half and full duplex discussed in below thread. However, I had a question on the handling of RS485 below GND. Would the multiplexer/switch CD4053…

  • over 1 year ago
  • Interface
  • Interface forum

• SN65HVD1473: SN65HVD1473

  

  Pavel Vencalek

  TI Thinks Resolved

  Part Number: SN65HVD1473 Hello, does SN65HVD1473 tri-states when it looses power? (both driver and receiver) Pavel

  • over 2 years ago
  • Interface
  • Interface forum

• SN65HVD1473: Using SN65HVD1473 in half duplex

  

  Karthik B

  TI Thinks Resolved

  Part Number: SN65HVD1473 Hi team, I need some clarity on SN65HVD1473 RS-485 transceiver. •Can I use the above IC in Half duplex mode by shorting its differential pins (ie; A with Y , B with Z) . Since my master has 2 wire output(half duplex) and…

  • over 3 years ago
  • Interface
  • Interface forum

• SN65HVD1473: RS485 Communication Issue

  

  Ashok Kumar18

  TI Thinks Resolved

  Part Number: SN65HVD1473 Other Parts Discussed in Thread: SN75176B , Hi, I'm using two RS485 transceivers to communicate between two controller cards. Below are the two different part no's SN75176B SN65HVD1473 SN75176B part works under 5 volt supply…

  • over 3 years ago
  • Interface
  • Interface forum
Answered

• SN65HVD1473: Difference between SN65HVD1473D & SN65HVD73D

  

  Karthik B

  Resolved

  Part Number: SN65HVD1473 Other Parts Discussed in Thread: SN65HVD73 Hi team, What is the difference between the SN65HVD1473D & SN65HVD73D , because in my previous board i was using SN65HVD1473D and it was working fine(i have converted this to half duplex…

  • Resolved

  • over 3 years ago
  • Interface
  • Interface forum
Answered

• SN65HVD1473: Switching between full and half duplex

  

  Roy Hsu

  Resolved

  Part Number: SN65HVD1473 Other Parts Discussed in Thread: CD4503B Hi there, My customer plans to use the following configuration to switch between full and half duplex mode with SN65HVD1473. My question is actually about how to select a suitable mux…

  • Resolved

  • over 3 years ago
  • Interface
  • Interface forum
Answered

• SN65HVD1473: Termination resistor in RS-485 mode.

  

  Oscar Gomez Fuente

  Resolved

  Part Number: SN65HVD1473 Hi everyone, I'm using the SN65HVD1473 transceiver in RS-485 mode. Does the termination resistor have to be Pulse-Proof? Best regards.

  • Resolved

  • over 4 years ago
  • Interface
  • Interface forum

• SN65HVD1473: Ackward RS-485 Weveforms.

  

  Oscar Gomez Fuente

  Part Number: SN65HVD1473 Other Parts Discussed in Thread: TIDA-00892 , ISOW7841 , Hi everyone, I'm checking a design, that it's basically this evaluation board with some adds to add RS-485 Half-Duplex and RS-485 Full-Duplex and RS-422 support: …

  • over 4 years ago
  • Interface
  • Interface forum
Answered

• SN65HVD1473: Can be used this IC for RS-422 purpose too?

  

  Oscar Gomez Fuente

  Resolved

  Part Number: SN65HVD1473 Hi everyone, I'm designing a shield board for the Raspberry Pi 3B with the possibility of using RS-485 or RS-422 (With some jumpers) and using a configuration similar to this scheme for activating the transmission pins with…

  • Resolved

  • over 4 years ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.