Search tips
Showing 29 results View by: Thread Post Sort by

  • SN65HVD23: Whether this transceiver can be used for power over communication interface application

    Answer Suggested
    Part Number: SN65HVD23 Other Parts Discussed in Thread: THVD8000 , , THVD8010 Hi, We have requirement for RS485 power over communication with data rate 10Mbps upto 500m cable distance. It is noted that the THVD8000 device can be used with two-wire cable…
    • Answered

  • SN65HVD23: Long Cable Length

    Resolved
    Part Number: SN65HVD23 Other Parts Discussed in Thread: THVD1429 Custome is looking for long length cable 100M with 12Mbps data rat and 3.3V bias power. for MD Encoder Application. In the SN65HVD23 d/s, it is able to extend cable length, but it only works…
    • Resolved
    • Answered

  • SN65HVD23: Is there a device like this one that allows more nodes?

    Resolved
    Part Number: SN65HVD23 Other Parts Discussed in Thread: SN65HVD24 , THVD1520 , THVD1550 , THVD1420 I'm trying to find an RS485 half-duplex transceiver that can handle over 100 nodes at a distance of over 100 meters and a speed over 10 Mbps (20-30 Mbps would…
    • Resolved

  • SN65HVD23: CAN IC Failure

    Part Number: SN65HVD23 Hi, My CAN Transciver is failing when the communication starts. Measured the transient voltage at the can lines, and observed that only+50 to -50V peak is there in CAN lines for 10uS. Will this peak lead to IC failure? What might…

  • SN65HVD23: Can this part replace a CAN transceiver bridge?

    Answer Suggested
    Part Number: SN65HVD23 Other Parts Discussed in Thread: TIDA-01487 Hi team, My customer is is currently using a CAN transceiver part that internally creates a bridge between two CAN bus branches. They are wondering if there is a way to replace this part…
    • Answered

  • RE: ISO1042: connection issue

    Resolved
    Hello Giorgio, The following block diagram makes sense and should work. Please keep in mind that you could also use ISO1042 to integrate the ISO7721 and one of the SN65HVD23. Best, Andrew

  • SN65HVD23: Driving Capability

    TI Thinks Resolved
    Part Number: SN65HVD23 Dear Team, I have a question for CAN transceiver SN65HVD23 series. In the datasheet, we can find the current is 17mA (max) for dominant/ recessive mode. But we also find output driver current is near to 35mA (If Vin=3.3V) So…
    • Answered

  • SN65HVD23: Propagation delay (SPRAC35)

    Resolved
    Part Number: SN65HVD235 Im facing difficulties on understanding the datasheet of SN65HVD235. I need the propagation delay of the device to use as input for the CAN Bit Timing calculatior (SPRAC35). The calculator uses: total propagation time = 2 x (delay…
    • Resolved

  • SN65HVD23: Layout Impedance for Bus Lines

    TI Thinks Resolved
    Part Number: SN65HVD23 Team, Typically we will need to have differential bus lines with 120ohm impedance and 120ohm termination resistors at the end. But if we use split termination, from our layout guide suggestion, is it still 120ohm differential pair…
    • Answered

  • SN65HVD23: Industrial Interface Forum

    Resolved
    Part Number: SN65HVD23 Hi, I wanted to know the current required(max current consumption) for the below mentioned parts SN65HVD233 SN65HVD234 SN65HVD235 Regards, Karthik
    • Resolved

Didn't find what you are looking for? Post a new question.