Search tips
Showing 16 results View by: Thread Post Sort by
    Answered

  • SN65LBC176: Vod of SN65LBC176

    Resolved
    Part Number: SN65LBC176 Hi team, Can I know why the min differential output voltage of SN65LBC176 is only 1.1V when RL=54ohm? Seems that the RS-485 standard is >1.5V? Regards, Xiaoying
    • Resolved
    • Answered

  • SN75LBC176: Differences between SN75LBC176 and SN65LBC176

    Resolved
    Part Number: SN75LBC176 Other Parts Discussed in Thread: SN65LBC176 , Hi team, Why is there a difference in the minimum differential output between SN75LBC176 and SN65LBC176? Is it the same if the temperature range is 0~70℃? Sincerely. Ryu
    • Resolved
    • Answered

  • SN65LBC176: Some question for RS422 application

    Resolved
    Part Number: SN65LBC176 Other Parts Discussed in Thread: SN75176A , Hi, RS422 and RS485 are electrical characteristics compatible, I have some questions below. 1. If SN65LVC176 datasheet is not mentioned RS422, could it use for RS422 application? 2. Is…
    • Resolved

  • SN65LBC176: Regarding some Oscillations Observed

    Part Number: SN65LBC176 There are two devices being used in the same application. Device "A" : SN65LBC176 Device "B" : SN65LBC176A It seems there are quite a few little differences between these two parts; timings and ESD protection…
    • Answered

  • RE: SN65LBC176: SN65LBC176D can be replaced with SN65LBC176AMDREP?

    Resolved
    Hello Parker-san, Thank you very much for spending a lot of time on this topic. I'll tell my customer that AMDREP device may work as D device, but please check carefully on their system because some of the specs are slightly different. Best Regards…
    • Answered

  • SN65LBC176-Q1: Rated and measurement specifications

    Resolved
    Part Number: SN65LBC176-Q1 Hello team, If you have the below information, can you share it with me? * SN65LBC176-Q1 is being considered as an alternative for SN65LBC1801DRQ1. 1. ESD rating 2. Temperature characteristics for VIT+ , VIT- and VOH, VO (-10℃~110…
    • Resolved

  • SN65LBC176-Q1: For 1PPS(1Hz) signal

    TI Thinks Resolved
    Part Number: SN65LBC176-Q1 Dear Team, Can SN65LBC176QDRQ1 transmit 1PPS(1Hz) signal as below waveform? If the customer use RS485 interface, is 1PPS_CH1_P & 1PPS_CH1_N need an RT resistor? BR Kevin
    • Answered

  • SN65LBC176-Q1: Schematic Review

    Resolved
    Part Number: SN65LBC176-Q1 Dear Team, Please help to double check the schematic. Is it ok the logic input is from 3.3V MCU and output is 5V logic? BR Kevin
    • Resolved

  • SN65LBC176: internal pull up resistor

    TI Thinks Resolved
    Part Number: SN65LBC176 Hi Team, my customer ask, if the internal pull up resistor is able to replace an external pull up if needed? What is the value of this internal pull up resistor? Thanks for your support. BR Martin
    • Answered

  • SN65LBC176-Q1: Impedance for SN65LBC176-Q1 when the device is powered off

    Resolved
    Part Number: SN65LBC176-Q1 Other Parts Discussed in Thread: SN65LBC173 Hi, I would like you to confirm impedance value of "D", "R", "A" and "B" pins in case of following condition. * SN65LBC176-Q1 is powered off…
    • Resolved

Didn't find what you are looking for? Post a new question.