• 

  Jason Dai

  • 9 months ago
  • Interface
  • Interface forum

  SN65MLVD200A: Is it allowed to short R-D and RE-DE?

  TI Thinks Resolved

  Part Number: SN65MLVD200A Hello E2E, Is it allowed to short R-D and RE-DE? what issue will occur? Please help to double check the schematic as attachment. Sincerely, Jason
• 

  Kent Butler

  • over 1 year ago
  • Interface
  • Interface forum

  SN65MLVD200A: Why do I see 6ns end to end delay on differential MLVDS signals with 10.5ft of 100 ohm twisted pair and 19 transceivers?

  Part Number: SN65MLVD200A I have a multi-drop M-LVDS network prototyped with 4-layer boards with a clock transceiver and a data transceiver for each of 19 nodes. The transmission line is CAT 5e with 100 ohm terminations at each end. The length of twisted...
• 

  Yaser Ibrahim

  • over 1 year ago
  • Interface
  • Interface forum

  RE: SN65MLVD200A: What is Junction Temperature of SN65MLVD200A Transceiver IC

  Hello, I don't have this data specifically, but you can probably use the inverse of the RθJA as an approximation. Regards, Yaser
• 

  Luke Sun

  • over 2 years ago
  • Interface
  • Interface forum

  SN65MLVD200A: Max voltage on pin A/B

  TI Thinks Resolved

  Part Number: SN65MLVD200A Hi team, My customer is using SN65MLVD200A, and they found that in their system bus, the chip's A/B pin will connect 5V power supply with a 4.7kohm pull-up resistor. In datasheet, the max condition is 4V for A/B pin....
• 

  Jan Volkering

  • over 4 years ago
  • Interface
  • Interface forum

  SN65MLVD200A multidrop connection issue

  Hi, My customer reports a communication problem with a 3-node RS485 multidrop connection using the SN65MLVD200A. Based on their failure report I concluded that the line terminations are not in order and also the termination resistor values to not...
• 

  Toshiyuki

  • over 5 years ago
  • Interface
  • Interface forum

  SN65MLVD200A / about the difference SN65MLVD200D and SN65MLVD200AD

  • Resolved

  Hi, Please let me know the difference SN65MLVD200D and SN65MLVD200AD ? In addition, I would like to know the reason why SN65MLVD200D isn't recommended. Best Regards, Kato
• 

  Youngho Suh

  • over 2 years ago
  • Clock & timing
  • Clock & timing forum

  CDCLVC1102: MLVDS 10MHz reference distribution help

  TI Thinks Resolved

  Part Number: CDCLVC1102 Hi, I Plan to use external 10MHz reference clock which produces differential signal (voltage out is 0.84Vlow - 1.6Vhigh). I want to distribute this signal to VPX backplane to be fed several cards that uses 10MHz reference. the...
• 

  Ryan Hashimoto

  • over 3 years ago
  • Interface
  • Interface forum

  RE: DS90LV032A: Roadmap of the logic Interface

  Hi Lacey, In regards to your questions about the devices being able to support hot plug, I consider a device to support hot plug if the inputs can support signals when the power supply is at 0V, and the GND is connected. Please make sure the GND is...
• 

  James Yea

  • over 6 years ago
  • Interface
  • Interface forum

  LVDS vs M-LVDS for clock distribution to multiple devices on multiple daughter boards

  I am looking for advice on clock distribution for an Oil and Gas well-monitoring application. The tool is likely to be 2m in length and I have to distribute a 25MHz clock to up to 10 daughter boards along that length. Some daughter boards contain up to...
• 

  Orlando Richardson

  • over 10 years ago
  • Interface
  • Interface forum

  SN65MLVD200A...modifying IBIS model

  TI Thinks Resolved

  Hello Team Can you please assist with the customer's inquiry below? Thank you Contact's Information Date Opened: 7/19/2010 02:23:04 PM Company Name: Aeroflex Contact Name: Tom Sutton Contact Phone: (949) 362-2260 x17 Contact...

Didn't find what you are looking for? Post a new question.

• Ask a new question