• SN74AHC1G126: Datasheet not found

  

  Pablo Gonzalez

  TI Thinks Resolved

  Part Number: SN74AHC1G126 Hi, I'm working on the analysis of an schematic using the part number "SN74AHC1G126MDCKTEP" but I can't find the datasheet of this, I also don't find this variation on "SN74AHC1G126" datasheet. I was wondering if this…

  • 9 months ago
  • Logic
  • Logic forum
Answered

• SN74AHC1G126-Q1: Clarification of recommended operating temperature range

  

  HP

  Resolved

  Part Number: SN74AHC1G126-Q1 Dear TI Support The datasheet for SN74AHC1G126-Q1 states a minimum recommended operating temperature of -55°C in section 6.3 Could you please confirm that this is correct as the rest of the datasheet refers to -40°C as…

  • Resolved

  • over 2 years ago
  • Logic
  • Logic forum
Answered

• SN74AHC1G126-Q1: Buffer with OE pin & Input Type as Schmitt Trigger ?

  

  KrnB

  Resolved

  Part Number: SN74AHC1G126-Q1 Other Parts Discussed in Thread: SN74LVC1G99-Q1 , SN74LVC2G17-Q1 , SN74LVC1G17-Q1 Hello, I looking for a Schmitt Trigger input version of SN74AHC1G126-Q1 but could not find one. Is there a Non-Inverting Buffer Part featuring…

  • Resolved

  • over 2 years ago
  • Logic
  • Logic forum
Answered

• SN74AHC1G126-EP: 74AHC1G126MDCKTEP

  

  Ankit Jain

  Resolved

  Part Number: SN74AHC1G126-EP Hi, I am simulating the behavior spice model of SN74AHC1G126-EP and observing one problem. When i am connecting the 3.3V source to OE pin with 10K in series, The voltage at OE pin is clamping to 550mV. When series resistance…

  • Resolved

  • over 5 years ago
  • Logic
  • Logic forum
Answered

• SN74AHC1G126-EP: ESD HBM Rating

  

  Carlo

  Resolved

  Part Number: SN74AHC1G126-EP Other Parts Discussed in Thread: SN74AHC1G126 Hi team, Good day. Our customer is requesting for the ESD HBM rating for 74AHC1G126MDCKTEP. Is the ESD HBM rating of non-EP version which is SN74AHC1G126 applicable? Regards…

  • Resolved

  • over 5 years ago
  • Logic
  • Logic forum

• SN74AHC1G126-EP: Output state until minimum VCC reaches during power up

  

  Cedrick

  TI Thinks Resolved

  Part Number: SN74AHC1G126-EP Hi, Good day. Our customer is using the SN74AHC1G126-EP and they have this inquiry below: During power up (slow rise of power), what will be the output state until minimum VCC limit is reached? Will it be output state 'Low…

  • over 5 years ago
  • Logic
  • Logic forum

• TPS7B69-Q1: Required IMDS submission

  

  Ajith Kumar

  TI Thinks Resolved

  Part Number: TPS7B69-Q1 Other Parts Discussed in Thread: TPS92633 , TPS92630-Q1 , SN74AHC1G126-Q1 Dear Supplier, I hope you are doing well! Can you please provide IMDS submission for the below part to the Belink IMDS ID 185359 . Thank you! …

  • 3 months ago
  • Power management
  • Power management forum
Answered

• SN74AXC8T245: Bidirectional TDM 4MHz buffer

  

  Robert Alfred Kecs

  Resolved

  Part Number: SN74AXC8T245 Other Parts Discussed in Thread: LSF0108 , , SN74AHC1G126 , SN74LVC2G126 , SN74AUP2G125 Tool/software: So i need change the voltage LVL of a TDM 4mHz buss from 1v8 to 3v3. TDM master also changes ( it is either on the 1v8 side…

  • Resolved

  • over 1 year ago
  • Logic
  • Logic forum

• ISO6741: Enable pin

  

  Ohad Bonneh

  TI Thinks Resolved

  Part Number: ISO6741 Other Parts Discussed in Thread: SN74AHC1G125 , ISO6762 , ISO6740 , ISOM8610 , SN74AHC1G126 Tool/software: Hi Team, for the ISO6741 in table 6.1 it states the following: Output enable 1. Output pins on side 1 are enabled when…

  • over 1 year ago
  • Isolation
  • Isolation forum
Answered

• RE: SN74LVC1G126: DoesTI has P2P solution can replace SN74LVC1G126DRLR?

  

  Albert Xu1

  Resolved

  Hi Marvin, You can try SN74AHC1G126 with Vcc = 2-5.5 or SN74AUC1G126 / SN74AUP1G126 with Vcc = 0.8-3.6. It will have to cater to your customer needs.

  • over 3 years ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.