Answered

• SN74AUC125: THERMAL INFO

  

  Abhijith S

  Resolved

  Part Number: SN74AUC125 Tool/software: Hi Please help to find the thermal data of the part SN74AUC125RGYR. Below are the datas we require: Max Allowed Tj (in degC) RThetaJC RThetaJB

  • Resolved

  • 5 months ago
  • Logic
  • Logic forum

• SN74AUC125: Typical Tpd value at 1.2V

  

  shivaji magadum

  Answer Suggested

  Part Number: SN74AUC125 Tool/software: Hello, I plan to use "SN74AUC125" on my test board to drive a 300MHz clock, the part will operate at 1.2V. I am looking for the typical value of Tpd under -25deg + 1.2V, as the datasheet provides propogation delay…

  • 8 months ago
  • Logic
  • Logic forum

• SN74AUC125: sn74auc125rgy thermal information

  

  Harrison Citrin

  TI Thinks Resolved

  Part Number: SN74AUC125 Hello, For part sn74auc125rgy, can you please provide the recommended operating junction temperature range and the absolute maximum junction temperature? Can you also provide the junction-to-case thermal resistance (degC/W)?…

  • over 1 year ago
  • Logic
  • Logic forum

• SN74AUC125: Do we have higher driving current buffer solution at 1.1V input voltage?

  

  Paul Yeh

  TI Thinks Resolved

  Part Number: SN74AUC125 Tool/software: Hi team, My customer need buffer solution that support 1.25V VCC voltage. But they need higher driving current in their application. In datasheet, this device's output current is only 3mA when Vcc=1.1V. I…

  • over 1 year ago
  • Logic
  • Logic forum

• SN74AUC125: what is the signal loss and output length can SN74AUC125 support?

  

  Ann_Lien

  TI Thinks Resolved

  Part Number: SN74AUC125 Hello expert, My customer is asking how long can SN74AUC125 on trace length. Also the loss on SN74AUC125. Could you provide the information for us? Thanks a lot! Best regards, Ann Lien

  • over 4 years ago
  • Logic
  • Logic forum

• SN74AUC125: Skew data

  

  Frank Rothoff

  TI Thinks Resolved

  Part Number: SN74AUC125 My customers request: I have to handle two 1.8V-SPI-Interfaces (each with 4 signals: CLK,CS,MOSI,MISO) between two components, which are sometimes partially powered. During “power-save-mode” In order to fulfill the SPI master…

  • over 4 years ago
  • Logic
  • Logic forum

• SN74AUC125: About IBIS model

  

  Tao_2199

  Part Number: SN74AUC125 Hello, Regarding to IBIS model on SN74AUC125,my customer is asking a question. (Question) The version of current IBIS model is 3.2. Do you have a IBIS model later than v3.2 on this device? Regards, Tao_2199

  • over 5 years ago
  • Logic
  • Logic forum

• SN74AUC125 Exposed Pad Connection

  

  Kevin Bell

  Hello, The datasheet does not specifically state what to connect the exposed pad of this part to. I assume you would connect it to ground but i want to confirm. Thank You, Kevin

  • over 11 years ago
  • Logic
  • Logic forum

• SN74AUC125 behavior when short duration pulse on OE

  

  RY9983

  Other Parts Discussed in Thread: SN74AUC125 6735.SN74AUC125_Waveform.pdf Hi, My customer observed strange behavior with SN74AUC125 as attached. Even though OE is in LOW state and input(A) is LOW, the output(Y) sometimes doesn't go LOW. {Yellow box…

  • over 14 years ago
  • Logic
  • Logic forum

• SN74LVC125A: I2S redriver for 800mm cable extension.

  

  Gary Teng

  TI Thinks Resolved

  Part Number: SN74LVC125A Other Parts Discussed in Thread: SN74AUC125 , SN74AUC34 Tool/software: Hi Sir, My customer need to extend its I2S length to 800mm for linking their two PCB boards. Is SN74LVC125 good for 1.8V I2S application? Or any other suggestion…

  • 7 months ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.