TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 14 results View by: Thread Post Sort by
    Answered
  • SN74AUC2G53: Control input voltage specification applies to which pins ?

    Jan Witte
    Jan Witte
    Resolved
    Part Number: SN74AUC2G53 Tool/software: Hello, in the device specification a control input voltage Vi is specified. Just to be sure, Vi is related to the pin A and INH ? Thank you, best regards Jan
    • Resolved
    • 6 months ago
    • Switches & multiplexers
    • Switches & multiplexers forum
  • Answered
  • SN74AUC2G53: Achieving 1 to 4 fanout: best practices within AUC logic family?

    John Silzel
    John Silzel
    Resolved
    Part Number: SN74AUC2G53 Other Parts Discussed in Thread: SN74AUC1G74 , LMK1C1104 Tool/software: I am doing a new design for a quadrature sampling detector in which an incoming RF signal must be sampled four times in one cycle. This requires switching…
    • Resolved
    • 6 months ago
    • Switches & multiplexers
    • Switches & multiplexers forum
  • SN74AUC2G53: input impedance of A? do I need to terminate line from LVCMOS 50 ohm source?

    pinhas rosenfelder
    pinhas rosenfelder
    Answer Suggested
    Part Number: SN74AUC2G53 Other Parts Discussed in Thread: LMK00101 , LMK00105 , Tool/software: I plan to drive the A input with a square wave of 160MHz to switch the inputs between Y1 and Y2. the source of this signal will be LMK00101 in one configuration…
    • 7 months ago
    • Switches & multiplexers
    • Switches & multiplexers forum
  • SN74AUC2G53: Is there a 4 position (SP4T?) version with similar switching speed?

    pinhas rosenfelder
    pinhas rosenfelder
    TI Thinks Resolved
    Part Number: SN74AUC2G53 Tool/software: Is there a similar part that can switch between 4 DC signals? If not - is it practical to cascade 3 of these devices to effectively switch between 4 DC level inputs at 1ns switching times? Or will there be timing…
    • over 1 year ago
    • Switches & multiplexers
    • Switches & multiplexers forum
  • Answered
  • SN74AUC2G53: floating supplies (GND as VCC and neg1.25V as Vee) to allow switching of negative DC voltage?

    pinhas rosenfelder
    pinhas rosenfelder
    Resolved
    Part Number: SN74AUC2G53 Other Parts Discussed in Thread: TMUX1133 , CD74HC4053 , Tool/software: I need to switch between 2 different negative voltages to the common output. The negative voltages range between 0V and -1V 1) Can I connect the Vcc…
    • Resolved
    • over 1 year ago
    • Switches & multiplexers
    • Switches & multiplexers forum
  • Answered
  • SN74AUC2G53: tpd plausibility

    Alfred Fuchs1
    Alfred Fuchs1
    Resolved
    Part Number: SN74AUC2G53 Propagation delay at Vcc=2.5V and 15pF load is given as 0.1ns. Footnote (1) says that this is the calculated RC-time constant with the typical on-state resistance and the load. For AUC1G66 the corresponding value is 0.1ns…
    • Resolved
    • over 2 years ago
    • Switches & multiplexers
    • Switches & multiplexers forum
  • Answered
  • SN74AUC2G53: SN74AUC2G53 break-before-make time

    user5182412
    user5182412
    Resolved
    Part Number: SN74AUC2G53 Other Parts Discussed in Thread: TMUX1219 , SN74AUC2G66 HI team, I am using the SN74AUC2G53 . I can not find the break-before-make parameter in the datasheet . As many other switch give the break-before-make number there , like…
    • Resolved
    • over 3 years ago
    • Switches & multiplexers
    • Switches & multiplexers forum
  • Answered
  • SN74AUC2G53: SN74AUC2G53 Vcc

    user5182412
    user5182412
    Resolved
    Part Number: SN74AUC2G53 Other Parts Discussed in Thread: TMUX1219 , SN74LVC1G3157 , SN74CBT3257 Hi, Team, We are considering using SN74AUC2G53 in a 3.3V system. As the recommended Vcc is 2.7V max , but the Absolute Maximum Ratings is limited to 3.6V…
    • Resolved
    • over 4 years ago
    • Switches & multiplexers
    • Switches & multiplexers forum
  • Answered
  • TMUX1248: Pins don't have output can choose

    Kevin Zhang
    Kevin Zhang
    Resolved
    Other Parts Discussed in Thread: TMUX1248 , SN74AUC2G53 Tool/software: Hi I have some problems about TMUX1248 IBIS model, pin 1,3,4 should be I/O(input and output) Pin Signal_name model_name 1 S2 nc 2 GND gnd …
    • Resolved
    • 10 months ago
    • Switches & multiplexers
    • Switches & multiplexers forum
  • RE: DS90LV011A: BUFFER TO CLOCK SIGNAL

    Lee Sledjeski
    Lee Sledjeski
    Hi Shlomi, The DS90LV011A does not include a mux function. I think a passive switch like the SN74AUC2G53 would work well for a 40 MHz application. www.ti.com/.../sn74auc2g53.pdf There are also some logic devices which could perform this function…
    • over 7 years ago
    • Interface
    • Interface forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question