Answered

• SN74AVC4T245-Q1: Chip peripheral circuit design

  

  Jade Lan

  Resolved

  Part Number: SN74AVC4T245-Q1 Other Parts Discussed in Thread: SN74AVC4T245 Tool/software: May I know if the peripheral circuit design of the chip in the figure is appropriate? The SN74AVC4T245 is mainly used here for level translation and the arrow in…

  • Resolved

  • 2 months ago
  • Logic
  • Logic forum
Answered

• SN74AVC4T245-Q1: SN74AVC4T245-Q1

  

  ?? ?

  Resolved

  Part Number: SN74AVC4T245-Q1 Other Parts Discussed in Thread: TXU0104-Q1 Tool/software: Hi ALL, when i am testing the current of VCCA,i found that VCCA has 2mA current, and when i conect 2A2 to gnd, zhe total current of VCCA decrease to 0.2mA. The…

  • Resolved

  • 11 months ago
  • Logic
  • Logic forum

• SN74AVC4T245-Q1: Request for Debug Support

  

  Sam Durai

  Part Number: SN74AVC4T245-Q1 Tool/software: Hi Team, I am using the 74AVC4T245QWBQBRQ1 part on my board. I am sending a continuous high pulse to the level translator, and when I probe the signal, I am getting <1V instead of 1.8V (VCCA = 1.8V). When…

  • 4 months ago
  • Logic
  • Logic forum

• SN74AVC4T245-Q1: Requesting soldering reflow profile

  

  Sandhiya Subashree M

  TI Thinks Resolved

  Part Number: SN74AVC4T245-Q1 Tool/software: Hi Team, Request you to share the reflow graph and reflow conditions for the part number 74AVC4T245QWBQBRQ1 Regards, M.Sandhiya Subashree

  • 6 months ago
  • Logic
  • Logic forum

• SN74AVC4T245-Q1: SN74AVC4T245-Q1 vs SN74AXC4T245-Q1

  

  Xiaoxiang Liu

  Answer Suggested

  Part Number: SN74AVC4T245-Q1 Other Parts Discussed in Thread: SN74AXC4T245-Q1 Hi team, Could you provide a comparison between the SN74AVC4T245-Q1 and the SN74AXC4T245-Q1? Are they able to use a 1kΩ pull-down resistor on the output side? Thanks…

  • over 1 year ago
  • Logic
  • Logic forum
Answered

• SN74AVC4T245-Q1: Request for 3D Model - 74AVC4T245QWBQBRQ1

  

  Sam Durai

  Resolved

  Part Number: SN74AVC4T245-Q1 Tool/software: Hi Team, I need 3D model (.stp) file for the part 74AVC4T245QWBQBRQ1 (for mechanical verification). Where can I get this? Regards, P. Sam Durai.

  • Resolved

  • 9 months ago
  • Logic
  • Logic forum
Answered

• SN74AVC4T245-Q1: Use Satellite project

  

  ? ??

  Resolved

  Part Number: SN74AVC4T245-Q1 Other Parts Discussed in Thread: SN54SC4T125-SEP Tool/software: Hello experts, We want to use SN74AVC4T245-Q1 to the satellite project. Are there any restrictions on using it on satellites? We are understanding that…

  • Resolved

  • 11 months ago
  • Logic
  • Logic forum

• SN74AVC4T245-Q1: Question about the requirement of input transition rise fall rate

  

  Xiaochen Gao

  TI Thinks Resolved

  Part Number: SN74AVC4T245-Q1 Tool/software: Hi TI Team, The datasheet specified a maximum rise or fall rate of 5ns/V. I want to know d oes the input signal still need to meet this requirement in the case of OE being pulled high and the device being…

  • 9 months ago
  • Logic
  • Logic forum

• SN74AVC4T245-Q1: when input pin(pin 2B2) is floating, the output pin (pin 2A2) is always high.

  

  gavin zhang

  TI Thinks Resolved

  Part Number: SN74AVC4T245-Q1 Other Parts Discussed in Thread: SN74AVC4T245 Dear TI support team, Our SN74AVC4T245-Q1 schematic is as follows, On one board, after I remove R3 and R6( that means the input pin and out pin are floating), the voltage…

  • over 1 year ago
  • Logic
  • Logic forum

• SN74AVC4T245-Q1: When the VCC voltage drops below what level will IO become high impedance?

  

  Jeff Yun

  TI Thinks Resolved

  Part Number: SN74AVC4T245-Q1 Other Parts Discussed in Thread: SN74AXC4T774-Q1 Hi, Team Hope you are doing well! When the VCC voltage drops below what level will IO become high impedance? I saw that SN74AXC4T774-Q1 is listed as 100mV, but there is…

  • over 1 year ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.