• SN74AVCH2T45: Vcc slew rate slower than recommend

  

  Manu Chang

  TI Thinks Resolved

  Part Number: SN74AVCH2T45 Tool/software: Hi expert, My customers are using SN74AVCH2T45 transmitting the 3.3V level to 1.8V level. For the 3.3Vcc, the slew rate is 5.8ns/V samller than the recommended min slew rate 5ns/V in datasheet, as in the waveform…

  • 3 months ago
  • Logic
  • Logic forum

• SN74AVCH2T45: What would possible happen if Vccb is before Vcca powered up

  

  Manu Chang

  TI Thinks Resolved

  Part Number: SN74AVCH2T45 Tool/software: Hi, My customers are hard to achieve this rule below in their design, hence they would like to ask: What would possible happen if Vccb is before Vcca powered up for SN74AVCH2T45? BR, Manu

  • 6 months ago
  • Power management
  • Power management forum
Answered

• SN74AVCH2T45: for UART communication

  

  Jay Yoo

  Resolved

  Part Number: SN74AVCH2T45 Other Parts Discussed in Thread: TXU0202 , SN74AXC2T245 Tool/software: Hi team, I'd like to double-check if SN74AVCH2T45 could be used on UART(push-pull) communications or not. Could you please check? Thanks, Jay

  • Resolved

  • over 1 year ago
  • Logic
  • Logic forum
Answered

• SN74AVCH2T45: • Maximum Data Rates of SN74AVCH2T45

  

  Dong Ba

  Resolved

  Part Number: SN74AVCH2T45 Hi team, Please help to provide the Maximum Data Rates of SN74AVCH2T45 @ 3.3V to 3.3V B.R. Eric

  • Resolved

  • over 4 years ago
  • Logic
  • Logic forum

• SN74AVCH2T45: Measurement Across the Diode

  

  Ray Vincent Aranzaso

  TI Thinks Resolved

  Part Number: SN74AVCH2T45 Other Parts Discussed in Thread: SN74AVCH8T245 Hi, Good Day. Customer had a question regarding SN74AVCH2T245 and SN74AVCH8T245. He connect either input pins or output pins or one of these two ICs to a circuit board node…

  • over 3 years ago
  • Logic
  • Logic forum

• SN74AVCH2T45: SN74AVCH2T45 input pull down resistor can't pull the input voltage to low

  

  Lijia Zhu

  TI Thinks Resolved

  Part Number: SN74AVCH2T45 Other Parts Discussed in Thread: SN74AXC2T45 Hi team, one question about SN74AVCH2T45 from my customer. There is an internal 33k pulldown resistor. They stop to send the signal when output is high. If they disconnect their…

  • over 4 years ago
  • Logic
  • Logic forum
Answered

• SN74AVCH2T45: Data rate

  

  FRANK1

  Resolved

  Part Number: SN74AVCH2T45 Hi Sir, SN74AVCH2T45 is a 2-Bit voltage translation. the data rate is 500 Mbps (1.8 V to 3.3 V). I wanna confirm this value is for one A1 or A2? each pin's data rate is max 500 Mbps Or this value is for A1+A2, each pin…

  • Resolved

  • over 5 years ago
  • Logic
  • Logic forum
Answered

• SN74AVCH2T45: SN74AVCH2T45DCUR Crash and memory issue

  

  manu

  Resolved

  Part Number: SN74AVCH2T45 Other Parts Discussed in Thread: SN74AXC2T45 Hi, When i connected refrence clock from ethernet PHY(AR8031) - 2.5V to i.MX 8 SoC - 3.3V my baord is getting crash and memory issue is coming. If i connected refrence clock directly…

  • Resolved

  • over 4 years ago
  • Logic
  • Logic forum
Answered

• RE: SN74AVCH2T45: SN74avch2t45

  

  Edoardo Lotti

  Resolved

  Hi, no, I don't need direction control pin (signal). I need unidirectional level shifter, but I have not found the unidirectional device. Do you have with the same speed characteristics? Thanks a lot.

  • over 8 years ago
  • Logic
  • Logic forum

• SN74AVCH2T45: SN74AVCH2T45 MDIO application

  

  Nanfang Liao

  TI Thinks Resolved

  Part Number: SN74AVCH2T45 Hello Team, My customer one project used this part and this project has been RTMed more than one year, and their systems run more than one year in the market and have no problem, recently customer feedbacked there are some…

  • over 8 years ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.