Answered

• SN74HC573A-Q1: SN74HC573A-Q1 AEC certification report

  

  Marc Liu

  Resolved

  Part Number: SN74HC573A-Q1 Hi Team, Customer need AEC certification report for SN74HC573A-Q1. Could you help provide it? Thank you! Marc

  • Resolved

  • over 2 years ago
  • Logic
  • Logic forum

• SN74HC573A-Q1: Quiescent current question

  

  Lanxi Li

  TI Thinks Resolved

  Part Number: SN74HC573A-Q1 Hello team, 1. What are the quiescent working current and normal working current of SN74HC573A-Q1? 2. How to understand the two parameters in the figure below? Best regards, Lanxi

  • over 2 years ago
  • Logic
  • Logic forum
Answered

• SN74HC573A-Q1: applying vil max or vih min at all input at once

  

  Yohann YVENOU

  Resolved

  Part Number: SN74HC573A-Q1 Hi everybody, We can see in datasheet that at VCC=6V, vil max=1.8 and vih min=4.2? Does it mean working with all inputs @ either vil max or vih min is allowed? We can see Texas documents as SZZA036B telling about vil…

  • Resolved

  • over 2 years ago
  • Logic
  • Logic forum

• SN74HC573A-Q1: Output probabilistic fault at the power up

  

  Songzhen Guo

  TI Thinks Resolved

  Part Number: SN74HC573A-Q1 Hi Experts,. SN74HC573A-Q1 is used in customer for BMS. The project is under DV. There is fault output of SN74HC573A-Q1, it will cause the whole system down. This device need be fixed before 9/10. So it can catch the PV…

  • over 3 years ago
  • Logic
  • Logic forum

• SN74HC573A-Q1: ESD level of SN74HC573A-Q1

  

  Fery Feng

  TI Thinks Resolved

  Part Number: SN74HC573A-Q1 Hi team, Could you please help to check the ESD level of SN74HC573A-Q1? Thanks

  • over 7 years ago
  • Logic
  • Logic forum

• SN74HC573A-Q1: Inquiry for spec of High-level input voltage when VCC=3.3V

  

  Eric Lai

  TI Thinks Resolved

  Part Number: SN74HC573A-Q1 Hi Expert, The engineer is asking the SN74HC573A-Q1 spec of High-level input voltage when VCC=3.3V. Pls advice.TKS. Best regards, Eric Lai Field Application Engineer Texas Instruments Taiwan Limited O: +886…

  • over 5 years ago
  • Logic
  • Logic forum
Answered

• SN74HC573A-Q1: Shared Pull-Down Resistor for Unused Channels

  

  Peiheng Liu

  Resolved

  Part Number: SN74HC573A-Q1 Hi, I am supporting customer for their design w TI SN74HC573A-Q1. It is a common knowledge that all unused input terminal should be tied to VCC or GND for determined state in each channel. Is it OK to pull down all the unused…

  • Resolved

  • over 7 years ago
  • Logic
  • Logic forum
Answered

• SN74HC573A-Q1: If some unused channel input and output pins are floating, will it influence other used channels?

  

  Johnny Guo

  Resolved

  Part Number: SN74HC573A-Q1 Hi, team, In SN74HC573-Q1 datasheet, unused input pin is recommend to tied to VCC or GND. But if some unused channel input and output pins are floating, will it influence other used channels? Thanks. Johnny

  • Resolved

  • over 6 years ago
  • Logic
  • Logic forum
Answered

• AND Gate Output State During Power-Up

  

  Peiheng Liu

  Resolved

  Other Parts Discussed in Thread: SN74HC573A-Q1 , SN74LVC2G08-Q1 Hi, I just went through these 2 threads from our forum and there are very helpful! Great thanks to Emrys! https://e2e.ti.com/support/logic/f/151/p/731172/2698649 https://e2e.ti.com…

  • Resolved

  • over 7 years ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.