• SN74LV07A: SN74LV07A damaged on several PCBAs

  

  Jaycee Bilbao

  TI Thinks Resolved

  Part Number: SN74LV07A Tool/software: Used SN74LV07A buffer IC on a tester circuit for vendor; recently had a case where 4 PCBAs were not working and analysis for all 4 points to damaged SN74LV07A; boards worked properly after replacing the part. Signal…

  • 3 months ago
  • Logic
  • Logic forum

• SN74LV07A: Looking for Compatible one

  

  Brian Wang0928

  TI Thinks Resolved

  Part Number: SN74LV07A Other Parts Discussed in Thread: SN74ACT17 Tool/software: Customer is looking for compatible device with MC74VHCT50ADTR2G. SN74LV07APWR is an open drain output that isn't suited on application. Regards Brian

  • 9 months ago
  • Logic
  • Logic forum

• SN74LV07A: SPICE model not working

  

  Quoc Ngo

  Part Number: SN74LV07A Using Xpedition AMS 2.11 and the SPICE model provided by TI. But getting this error: Error on division by zero inside the expression {(-ABS((1+SGN(V(VTP_DIFF,VEE))))/2*2*MAXICC*((V(IN,VEE)-(V(VCC,VEE)-VT))/V(VCC,VEE))^2)*(1…

  • over 3 years ago
  • Logic
  • Logic forum
Answered

• SN74LV07A: SN74LV07A:Undershoot

  

  user6213590

  Resolved

  Part Number: SN74LV07A Hello. According to the SN 74 LV07A datasheet, the undershoot voltage is -0.5 V. Is there any risk if the undershoot voltage is lower than -0.5 V? We observed -1V/1.5ns, that should be ok or not? Best regards. Jungo

  • Resolved

  • over 6 years ago
  • Logic
  • Logic forum

• SN74LV07A: Offline Support Request

  

  user5982066

  TI Thinks Resolved

  Part Number: SN74LV07A I am using LV07 in the switch circuit. The output pin of LV07 is used in applications where Hi-Z output and Low output are periodically repeated. However, it may be disturbed by disturbance crosstalk at Hi-Z output. As an example…

  • over 6 years ago
  • Logic
  • Logic forum

• SN74LV07A: Max junction Temperature

  

  owen lin

  TI Thinks Resolved

  Part Number: SN74LV07A Dear Team, When the measured case temperature of SN74LV07A becomes 85-degree Celsius, will the IC gets damaged? Thank you.

  • over 7 years ago
  • Logic
  • Logic forum
Answered

• SN74LV07A: 3.3V to 5V Buffer finding

  

  Cheney_Sun

  Resolved

  Part Number: SN74LV07A Other Parts Discussed in Thread: SN74AHCT244 Hi TI EE Please help to suggest a Buffer. 5V VCC,and have the function to change 3.3V Voltage level to 5V Voltage level.Not Open Collector. And do not need pull up .5V output driver…

  • Resolved

  • over 7 years ago
  • Logic
  • Logic forum
Answered

• SN74LV07A: VOH at different load conditions

  

  Ting Ye

  Resolved

  Part Number: SN74LV07A Hello Team, In SN74LV07A datasheet page 5, there are VOL at different load test conditions. May I know if VOH specs are the same with VOL at different loads? For instance, in conditions of Iout 16mA, -40C to 125C, VOL max is 0…

  • Resolved

  • over 7 years ago
  • Logic
  • Logic forum
Answered

• SN74LV07A: Similar part

  

  Amanda Ross95

  Resolved

  Part Number: SN74LV07A Other Parts Discussed in Thread: SN74LVC1G99 , SN74AUP1G99 , SN74AHC125 Hello there, I'm wondering if we have a similar device to this hex buffer but with open-collector outputs and hysteresis? I checked ESP but was unable…

  • Resolved

  • over 8 years ago
  • Logic
  • Logic forum
Answered

• SN74LV05A: Absolute Maximum Ratings of Output Voltage Range

  

  Yuichiro Kimura

  Resolved

  Part Number: SN74LV05A Other Parts Discussed in Thread: SN74LV07A Hello, Support team I have a question about SN74LV05A. When Vcc = 3.3 V, we are considering pull-up 5 V to the output pin. Is the following content correct? 7.1 Absolute Maximum Ratings…

  • Resolved

  • over 7 years ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.