• SN74LV1T125-Q1: Errata

  

  Taku Murayama

  TI Thinks Resolved

  Part Number: SN74LV1T125-Q1 Tool/software: Hi, Do you have errata information for SN74LV1T125QDCKRQ1? BR, Taku

  • 20 days ago
  • Logic
  • Logic forum

• SN74LV1T125: 5V -> 1.8V & 1.8V -> 5V Level shift,

  

  GARETH OU

  TI Thinks Resolved

  Part Number: SN74LV1T125 Other Parts Discussed in Thread: TXU0204 , SN74AHCT244 , SN74LXC8T245 , TXS0108E , TXU0104 Tool/software: Hi In the previous product, the following was used: SN74LV244APWR, 5V -> 3.3V Level shift SN74AHCT244PWR, 3.3V -> 5V Level…

  • 7 days ago
  • Logic
  • Logic forum
Answered

• SN74LV1T125: Use it as 5V to 1.8V down shifter

  

  diverger

  Resolved

  Part Number: SN74LV1T125 Tool/software: Hi, I want the input can safely accept 5V/3.3V/1.8V levels, and convert them to 1.8V. As SN74LV1T125 can tolerant 5V input when powered by 1.8V supply, so I expect I can achieve my goal with it. But the datasheet…

  • Resolved

  • 28 days ago
  • Logic
  • Logic forum

• SN74LV1T125: Used as 5V to 1.8V level shifter

  

  diverger

  TI Thinks Resolved

  Part Number: SN74LV1T125 Tool/software: Hi, As the input is 5V tolerant, I wonder if it's safe to use it as a 5V to 1.8V level shifter? If so, why the datasheet only state it can do '5V to 3.3V' but no mention '5V to 1.8V'? Thanks…

  • 3 months ago
  • Logic
  • Logic forum

• SN74LV1T125: Abnormal buffer operation

  

  ?? ?

  TI Thinks Resolved

  Part Number: SN74LV1T125 Tool/software: Hello, I'm Geon Hee. The signal from the DSP is inputted to the gate driver through the buffer. However, the current DSP signal is coming out well, and the buffer output signal is about 1.4 volts and does not…

  • 4 months ago
  • Logic
  • Logic forum

• SN74LV1T125: output is LOW when buffer is disabled

  

  Kranky

  TI Thinks Resolved

  Part Number: SN74LV1T125 Hi, I have a pretty straight forward circuit at hand. I am using 1 input AND gate and it's output is fed to buffer with active LOW enable. The circuit is working fine for the case when buffer is enabled ( buffer output is…

  • 7 months ago
  • Logic
  • Logic forum
Answered

• SN74LV1T125: Logic forum

  

  Fabrice GAUBIL

  Resolved

  Part Number: SN74LV1T125 Hi, I try to use a SN74LV1T125DBVR in my design as an interface between a 3.3V CMOS device and a 5V TTL device. I use it like this : Input A > pin 2 > GPIO Signal 0V or 3.3V Ouput Y > pin 4 > GPIO Signal 0V or 5V VCC…

  • Resolved

  • 8 months ago
  • Logic
  • Logic forum
Answered

• SN74LV1T125: OE pin can support 3.3V when VCC=1.8V?

  

  GW

  Resolved

  Part Number: SN74LV1T125 Hi, Team Our customer prefer to check with: if the VCC is 1.8V, can we use the 3.3V for OE pin? from our datasheet page 5, "7.3 Recommended Operating Conditions", the VI is from 0-5.5V, so i suppose it can support 3.3V for OE…

  • Resolved

  • 9 months ago
  • Logic
  • Logic forum
Answered

• SN74LV1T125: Thermal Information on DBV Package

  

  Shinichi Yokota

  Resolved

  Part Number: SN74LV1T125 Hello, SN74LV1T125's data sheet only specifies Θ JA as thermal parameter, but could you also provide such thermal parameters as Θ JC , Θ JB , Ψ JT , and Ψ JB ? Best regards, Shinichi Yokota

  • Resolved

  • over 1 year ago
  • Logic
  • Logic forum

• SN74LV1T125: spec check

  

  GARETH OU

  TI Thinks Resolved

  Part Number: SN74LV1T125 Other Parts Discussed in Thread: SN74LVC1G125 , SN74LVC1G34 , SN74AHC1G125 , TXS0102 , TXB0302 Hi Could you help confirm if there are any other suggestions 1 bit level shift IC Level Shifter from 5v to 3.3v Will use SN74LV1T125 …

  • over 1 year ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.