• SN74LVC2G14: looking a part with OE function

  

  Zoe Ko

  TI Thinks Resolved

  Part Number: SN74LVC2G14 Other Parts Discussed in Thread: SN74LVC2T45 Hi team, We used the SN74LVC2G14 before. However, we want a inverter with a OE(output enable) function. VCC : 5V Enable control signal : 1.8~3.3V 2 channel Do you…

  • over 6 years ago
  • Logic
  • Logic forum
Answered

• SN74LVC2G14: Chip Layout Clarification

  

  Dylan Barton

  Resolved

  Part Number: SN74LVC2G14 I just need to be able to confirm that the chip layout follows the standard of having pin 1 be under the larger vertical bar that can be found on the side of the physical chip. I can not find any definitive description of the…

  • Resolved

  • over 7 years ago
  • Logic
  • Logic forum
Answered

• SN74LVC2G14: datasheet layout example

  

  Daniel Ka

  Resolved

  Part Number: SN74LVC2G14 Hello all, I always like it when a datasheet provides layout hints. For the SN74LVC2G14, the datasheet shows the following layout example: I assume that the 0.1 µF capacitor is meant to operate as a bypass capacitor…

  • Resolved

  • over 7 years ago
  • Logic
  • Logic forum

• SN74LVC2G14: Output can't not work normally when connect the two channel as two stage inverter

  

  Tess Chen

  Part Number: SN74LVC2G14 Other Parts Discussed in Thread: SN74LVC1G17 Hi, I try to use the part as the figure shown above. Description: the input for the first channel Vin=0.1V, when connected as the figure above the output pin6 don't appear a high…

  • over 5 years ago
  • Logic
  • Logic forum

• SN74LVC2G14: Documentation missin

  

  Topi Rinkinen

  TI Thinks Resolved

  Part Number: SN74LVC2G14 Hi, The datasheet (11-May-2017): http://www.ti.com/lit/ds/symlink/sn74lvc2g14.pdf PDF page 15 shows tape dimensions from two projections, but neglects to tell wether this is 1st or 3rd ange projection. From the documentation…

  • over 7 years ago
  • Logic
  • Logic forum

• SN74LVC2G14-Q1: Need the (VIH VIL VOH VO) tolerance information from low and high temperature rating

  

  Eric Lai

  TI Thinks Resolved

  Part Number: SN74LVC2G14-Q1 Hi Expert, The engineer is asking the (VIH VIL VOH VO) tolerance information from low and high temperature rating. Thanks Best regards, Eric Lai Field Application Engineer Texas Instruments Taiwan Limited…

  • over 4 years ago
  • Logic
  • Logic forum
Answered

• UCC27321: Orientation UCC27321 an SN74LVC2G14

  

  Joaquim Santos

  Resolved

  Part Number: UCC27321 Hello, I want to mount the two abovementioned IC's on a PCB but I've no clue about the orientation and the pin numeration. Each IC is marked with a horizontal line that must indicate the orientation but, in the datasheet, there…

  • Resolved

  • over 7 years ago
  • Power management
  • Power management forum

• SN74LVC2G14: Application for UART with a 3 meter cable

  

  Antony Lin

  TI Thinks Resolved

  Part Number: SN74LVC2G14 Other Parts Discussed in Thread: SN74LVC2G04 , SN74LVC1G3157 Hi, My customer is using SN74LVC2G14 for an application with topology as below. The 3 meter cable is connected between two systems. TMC module output UART TX-->…

  • over 8 years ago
  • Logic
  • Logic forum
Answered

• SN74LVC2G14 / Bypass Capacitor

  

  Kuramochi Tadahiko

  Resolved

  Other Parts Discussed in Thread: SN74LVC2G14 Hi, On the datasheet, the capacitor 0.1uF is connected between Vcc pin and VDD. Is it correct? Thanks, Kuramochi

  • Resolved

  • over 9 years ago
  • Logic
  • Logic forum
Answered

• sn74lvc2g14 vs sn74lvc1g14 - differing electrical characteristics

  

  Adam Mujaj

  Resolved

  I'm looking at the single and dual schmitt-trigger inverters in the LVC series. However, I notice that they have differing positive and negative going thresholds: E.g. For Vcc = 3V: Vt+ min Vt+ max Vt- min Vt- max 1G 1.5V 1…

  • Resolved

  • over 10 years ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.