Answered

• SN74LVC541A: successor of SN74LVC541A

  

  Toshiro Imi

  Resolved

  Part Number: SN74LVC541A hello, Our customer is looking for new generation or successor of SN74LVC541A. Could you please help our customer to know the new or latest version of SN74LVC541A. Best regards,

  • Resolved

  • 1 day ago
  • Logic
  • Logic forum

• SN74LVC541A: Seeking Recommendation for a Buffer IC Shorter than SN74LVC541's VQFN

  

  SHH

  TI Thinks Resolved

  Part Number: SN74LVC541A Other Parts Discussed in Thread: SN74LVC244A Hi Team, Do we have recommendations for a Buffer IC that is shorter in height than the SN74LVC541's VQFN (H=1.0mm) package? Best regards, Scott

  • 2 months ago
  • Logic
  • Logic forum
Answered

• SN74LVC541A: VOL vs IOL characteristics

  

  Shunsuke Yamamoto

  Resolved

  Part Number: SN74LVC541A Hi team, On the datasheet, VOL parameters are described, but only 5 VOL variants by IOL parameters. How do we estimate the VOL vs IOL characteristics? Because there is no linear characteristics between VOL and IOL. Best regards…

  • Resolved

  • 3 months ago
  • Logic
  • Logic forum
Answered

• SN74LVC541A: Unspecified input signal transition rate.

  

  Bill Mackin

  Resolved

  Part Number: SN74LVC541A The 2014 revision of the SN74LVC541A datasheet, in section 10.2.2, says to see the dt/dV values in the Recommended Operating Conditions table. The dt/dV values are not in that table. I searched this forum and found WhitePaper…

  • Resolved

  • 5 months ago
  • Logic
  • Logic forum
Answered

• SN74LVC541A: min pulse width

  

  Ryoma Ohashi

  Resolved

  Part Number: SN74LVC541A Hi team, My customer might use this device with a input signal that contains some sharp pulse noise. So, could you tell us the maximum pulse width that this device doesn't recognizes as HIGH signal Regards, Ohashi

  • Resolved

  • 11 months ago
  • Logic
  • Logic forum

• SN74LVC541A: Excessive propagation delay time (~18ns instead of 5)

  

  Bill Mackin

  TI Thinks Resolved

  Part Number: SN74LVC541A One of our programs is using this part at 3.3V and started seeing part failures. When they replace this component, the board works again. We sent the failing parts, and new-from-stock parts to our lab for testing. The lab used…

  • over 1 year ago
  • Logic
  • Logic forum

• SN74LVC541A: maximum length of limitation

  

  Fred Cheng

  TI Thinks Resolved

  Part Number: SN74LVC541A Hi team, my customer want to use this device to redrive eSPI, there's a cable between buffer and UDC board, they want to know how long can this cable be to fully redrive the 50MHz signal, (buffer is placed between MB and…

  • over 1 year ago
  • Logic
  • Logic forum

• SN74LVC541A: SN74LVC541A Simulation Error

  

  Mark Philip Felipe

  TI Thinks Resolved

  Part Number: SN74LVC541A Other Parts Discussed in Thread: SN74LV541A Hi Team, Seeking your inputs. The PSpice model for the SN74LVC541A Octal Buffer contains a subcircuit (LOGIC_TRI_STATE_OUTPUT_LVC_1i_AND_Tristate_CMOS_SN74LVC541A IN OUT OEZ VCC VEE…

  • over 2 years ago
  • Logic
  • Logic forum

• SN74LVC541A-Q1: Latch up performance function

  

  Steven(Shenzhen) Shi

  TI Thinks Resolved

  Part Number: SN74LVC541A-Q1 Other Parts Discussed in Thread: SN74CB3Q3245 Hi there, My customer used SN74CB3Q3245 for signal swtich. They are confused with 'Latch-up performance'. So could you give me an explanation about this function? I can…

  • over 2 years ago
  • Logic
  • Logic forum
Answered

• SN74LVC541A: Is 5V on Vcc ok for part?

  

  Edmond Ng

  Resolved

  Part Number: SN74LVC541A Other Parts Discussed in Thread: SN74AHCT541 Is 5V ok to be applied to pin 20 Vcc of SN74LVC541APWR? The recommended is 3.3V, but I see the max rating is 6.5V. So does that mean 5V Vcc is ok? That means the output will be 5V with…

  • Resolved

  • over 2 years ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.