Answered

• SN74LVT245B: theta JB for SN74LVT245BPW

  

  Noriyuki Takahashi

  Resolved

  Part Number: SN74LVT245B Tool/software: Hi team Could you give any information of theta JB for SN74LVT245BPW? Regards, Noriyki Takahashi

  • Resolved

  • 10 months ago
  • Logic
  • Logic forum

• SN74LVT245B: When OE is Lo at power up

  

  Hiroaki Yuyama TED

  TI Thinks Resolved

  Part Number: SN74LVT245B Tool/software: Dear, Logic Support team. If the OE# and A[n] pins are connected to GND, could you let me know the behavior of Y[n] pin during Vcc ramp up from 0V to 2.7V? Best Regards, Hiroaki Yuyama

  • 10 months ago
  • Logic
  • Logic forum

• SN74LVT245B: Life Cycle Survey and Shock and Vibration Test data

  

  Rangegowda B V

  TI Thinks Resolved

  Part Number: SN74LVT245B Dear Team, Could please share the below information? 1. Shock and Vibration test data 2. Life cycle survey Supplier Supplier Part Number Component lead time Supplier Est for Part Life Cycle…

  • over 2 years ago
  • Logic
  • Logic forum
Answered

• SN74LVT245B: Pull up resistor for SN74LVT245B?

  

  shanthi s

  Resolved

  Part Number: SN74LVT245B Hi, I want to add pull up resistor in the input side for 5volt. Can you please help me to select a pull up resistor value limit? Thank you in advance.

  • Resolved

  • over 8 years ago
  • Logic
  • Logic forum
Answered

• SN74LVT245B: SN74LVT245B / Dynamic power-dissipation capacitance

  

  S.Satoshi

  Resolved

  Part Number: SN74LVT245B Other Parts Discussed in Thread: SN74LVC245A Hi, Now I'm studying how to calculate power consumption of logic devices. I checked FAQ in logic forum and checked app note SCAA035B. Then I studied that Dynamic power-dissipation…

  • Resolved

  • over 8 years ago
  • Logic
  • Logic forum

• RE: SN74LVT245B: Ensuring high-impedance state during start-up, power up

  

  Dylan Hubbard

  Hi, Sorry I didn't mean to mark that as resolved. The outputs will go into Hi-z in which there will be a leakage current spec'd in the datasheet. It's possible for that current to go through the LED however it would be in the uA range.

  • over 6 years ago
  • Logic
  • Logic forum

• SN74LVT245B: Bus transceiver

  

  Chaithra K C

  TI Thinks Resolved

  Part Number: SN74LVT245B We are using the Component (Part No.:SN74LVT245B), it is working working fine. But, the requirement is as attached. Please mention any Bus transceiver for the following specifications as attached. Best Regards, Chaithra

  • over 7 years ago
  • Logic
  • Logic forum
Answered

• SN74LVT245B: Output Impedance ?

  

  Kévin Stoffels

  Resolved

  Part Number: SN74LVT245B Other Parts Discussed in Thread: SN74LVC245A , SN74LVCR2245A Dear Sirs, I want to use the SN74LVT245B level shifter in order to protect my processor from backpowering on a RGMII interface. The processor, which has its own power…

  • Resolved

  • over 8 years ago
  • Logic
  • Logic forum
Answered

• SN74LVT245B: Is there a clamp protection diode on the A/B pin?

  

  rengui sun

  Resolved

  Part Number: SN74LVT245B Is there a clamp diode on the 245 pin? BB0~BB7 of A1~A8 are key signals, and FPGA_BB0~FPGA_BB7 of B1~B8 are FPGA input signals. 245 will be damaged when the button is pressed live. In series with a 100Ω resistor between BB0~BB7…

  • Resolved

  • over 7 years ago
  • Logic
  • Logic forum

• SN74LVT245B: Octal buffer seeing intermittent/latent failures where one or more channels are latching output either high or low.

  

  anonymous2486

  TI Thinks Resolved

  Part Number: SN74LVT245B We have been using the SN74LVT245BPW to transmit switching signals ranging from 200kHz to 35MHz. The input is driven directly by a Cyclone V FPGA at 3.3V and the output drives the input of an isolator IC with 125Ω thevenin resistor…

  • over 6 years ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.