• SN74LXC8T245-Q1: Simulation of Output-Pins - Ringing

  

  Michael Rauls

  TI Thinks Resolved

  Part Number: SN74LXC8T245-Q1 Other Parts Discussed in Thread: TINA-TI Hello, in our new design I use SN74LXC8T245QPWRQ1 for voltage translation 3.3V -> 5V. The circuit drives an external component (no design of our own). The external component has parallel…

  • 3 months ago
  • Logic
  • Logic forum
Answered

• SN74LXC8T245-Q1: Need IBIS model for DGS package type

  

  Jim Brinkhurst1

  Resolved

  Part Number: SN74LXC8T245-Q1 Hi experts I am designing with the CLXC8T245QDGSRQ1 version of this device (VSSOP package). The existing IBIS model only supports the TSSOP, VHQFN and UQFN package types, not the VSSOP. Please provide an IBIS model for the…

  • Resolved

  • 3 months ago
  • Logic
  • Logic forum

• SN74LXC8T245-Q1: Ways to test functionality of level shifter?

  

  Jack Zhang

  TI Thinks Resolved

  Part Number: SN74LXC8T245-Q1 Other Parts Discussed in Thread: SN74LXC8T245 , Hi all, I would like to seek advice on the best and most straightforward way of verifying the voltage translation functions of a level shifter part on a test backplane PCB design…

  • 4 months ago
  • Logic
  • Logic forum

• SN74LXC8T245-Q1: SN74LXC8T245-Q1

  

  ARJUN P.BHASKAR

  TI Thinks Resolved

  Part Number: SN74LXC8T245-Q1 Hi team, Is there any requirement of pull up resistors for the I/O 's pin in the respective IC for not keep floating?

  • 8 months ago
  • Logic
  • Logic forum
Answered

• SN74LXC8T245-Q1: Need for external pull-ups on control inputs

  

  Kshitish Gadre

  Resolved

  Part Number: SN74LXC8T245-Q1 I understand from the datasheet that SN74LXC8T245-Q1 has weak internal pull-downs of 5-MΩ, which set the default direction of the device from B to A and keeps it enabled all the time. But I want the device to be normally disabled…

  • Resolved

  • 6 months ago
  • Logic
  • Logic forum

• SN74LXC8T245-Q1: Temperature stress cycles - Device robustness

  

  Josef Alt

  TI Thinks Resolved

  Part Number: SN74LXC8T245-Q1 My customer plan to use CLXC8T245QRHLRQ1 in a fairly severe environment., ie the assembled boards must withstand: 1200 cycles between -40 / + 125 ° C. DFN or QFN packages assembled on PCB are generally not the most resistant…

  • over 1 year ago
  • Logic
  • Logic forum

• SN74LXC8T245-Q1: Part differences & use cases

  

  Emil Erickson

  TI Thinks Resolved

  Part Number: SN74LXC8T245-Q1 Other Parts Discussed in Thread: SN74AXC8T245 , SN74LXC8T245 Hi, I have a customer that's looking to replace the SN74AXC8T245. I want to recommended the SN74LXC8T245-Q1, but I'm unsure of a few key parameters. Is there a…

  • over 2 years ago
  • Logic
  • Logic forum
Answered

• SN74LXC8T245-Q1: VCC isolation feature

  

  Yuta Kurimoto

  Resolved

  Part Number: SN74LXC8T245-Q1 Other Parts Discussed in Thread: SN74AXC4T245-Q1 , TXU0104 , TXU0204 Hello Team, I have some question about VCC isolation feature of SN74LXC8T245-Q1 Q. In customer usecase, A1=input, Vcca=1.8V, B1=Output, Vccb=3.3V. If they disable…

  • Resolved

  • over 2 years ago
  • Logic
  • Logic forum

• RE: SN74LVC8T245: Alternate P/N required SN74LVC8T245RHLR

  

  Clemens Ladisch

  There are some SN74LVC8T245-EP devices available. But you should use the modern replacement, SN74LXC8T245(-Q1).

  • 5 months ago
  • Logic
  • Logic forum

• RE: SN65LVELT23: sharp edge output buffer with level translation, enable control, low prorogation delay and less part skew

  

  Joshua Salinas

  Hello, For 1.8 V to 5.0 V, we have the LXC family. The SN74LXC8T245 is rated from 1.1 V to 5.5 V with an enable pin. However, the prop delay is a little higher one these devices. For 1.8 V to 3.6 V, we have the TXV family. The TXV0108-Q1 is rated from…

  • 2 months ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.