• SN75LVPE802: SN75LVPE802

  

  Penn Zhang

  TI Thinks Resolved

  Part Number: SN75LVPE802 Other Parts Discussed in Thread: SN75LVPE801 , Hi， Are SN75LVPE802， SN75LVPE801 are linear rediver? Thank you.

  • over 6 years ago
  • Interface
  • Interface forum

• SN75LVPE802: Threshold detector, Squelch timer and OOB

  

  David Park

  TI Thinks Resolved

  Part Number: SN75LVPE802 Hi, Please check below 2 questions. 1. Is Threshold detector and squelch timer in below block same as OOB? This is redriver block diagram from Intel. 2. V(OOB) Input OOB threshold is OOB entry threshold? 3. What…

  • over 4 years ago
  • Interface
  • Interface forum

• SN75LVPE802: SN75LVPE802

  

  mark kelly

  TI Thinks Resolved

  Part Number: SN75LVPE802 Other Parts Discussed in Thread: DS125BR111 , DS80PCI102 , TUSB1002A I am interested in adding your PCI Express Redriver to my design and need the footprint file and schematic diamgram file to be used in Alegra PWB design application…

  • over 7 years ago
  • Interface
  • Interface forum

• SN75LVPE802: SN75LVPE802 TX OOB test fail

  

  kerr chang

  TI Thinks Resolved

  Part Number: SN75LVPE802 Hi team We test SATA have fail for OOB. and we have remove TI redriver , This test item will be pass. Could you help check this issue Have redriver : the red side , some Bit signals will be missing at the beginning. …

  • over 7 years ago
  • Interface
  • Interface forum

• SN75LVPE802: What level of DEW2 (pin 6) is recommended to be set when using transfer rate of 3Gbps by SATA?

  

  Matthew Chen

  TI Thinks Resolved

  Part Number: SN75LVPE802 Hi team, There are two questions about SN75LVPE802 1. What level of DEW2 (pin 6) is recommended to be set when using transfer rate of 3Gbps by SATA? If set to low, what will be the effect on signal function and quality? …

  • over 4 years ago
  • Interface
  • Interface forum
Answered

• SN75LVPE802: AC coupling cap placement and post-channel length

  

  Cindy Chang

  Resolved

  Part Number: SN75LVPE802 Hi team, May I know that is there any recommendation placement of AC coupling capacitors at differential inputs and outputs? What is the range of post-channel length could be? Is there a minimum and maximum? Thank you…

  • Resolved

  • over 5 years ago
  • Interface
  • Interface forum
Answered

• RE: SN75LVPE802: SN75LVPE802 series connection between Host and Device.

  

  Kawai

  Resolved

  Hi Lee-san, Thanks for your support. I am asking the transmission path (insertion loss) detail, so I will let you know when I obtain the information. Why would you not recommend series connection of SN75LVPE802 ? What kind of problem would be seen…

  • over 7 years ago
  • Interface
  • Interface forum
Answered

• SN75LVPE802: Need SI Model files

  

  Paul Yeh

  Resolved

  Part Number: SN75LVPE802 Other Parts Discussed in Thread: SN75LVCP601 , Hi Team, My customer would like to study this devices and please provide SI model (s parameter format) for their doing SI simulation. Thanks

  • Resolved

  • over 5 years ago
  • Interface
  • Interface forum
Answered

• SN75LVPE802: SN75LVPE802 input & output P&N swap

  

  Terry Wu2

  Resolved

  Part Number: SN75LVPE802 Hello Sirs, Is this chip support SATA 3.0 input polarity and output polarity swap at the same time just for layout consideration ? Many thanks !

  • Resolved

  • over 8 years ago
  • Interface
  • Interface forum

• SN75LVPE802: Pull up resistor and pull down resistor requirement

  

  Dylan Zheng

  TI Thinks Resolved

  Part Number: SN75LVPE802 Dear expert, As the datasheet table 1 shown, the SN75LVPE802 incorporates programmable equalization. The user can NC, pull high or pull low the related DE/EQ pins to tune. What's the requirement of these pin's pull up resistor…

  • over 5 years ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.