TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 43 results View by: Thread Post Sort by
    Answered
  • RE: Suggestions for USB PD and USB Audio to source the SmartAmp TAS5768M

    Benjamin Brammer
    Benjamin Brammer
    Resolved
    Hey Alex, yes your link was helpful and showed me some other possibilities but I don't need that kind of codec, since the TAS5768M has some built in DSP capability. I just need one USB PD controller and an USB audio codec delivering me the I2S audio…
    • over 8 years ago
    • Interface
    • Interface forum
  • Answered
  • RE: TAS5768M: Suggestions for USB PD and USB Audio to source the SmartAmp

    Roy Hsu
    Roy Hsu
    Resolved
    Hi Benjamin, I am not familiar with USB products and standards so please allow me to circle back to you after discussing with people of more knowledge on it. You can also post you questions here where experts of USB-C are at: e2e.ti.com/.../1008…
    • over 8 years ago
    • Audio
    • Audio forum
  • Answered
  • About ADR1 and ADR2 pin of TAS5768M

    Satoshi
    Satoshi
    Resolved
    Other Parts Discussed in Thread: TAS5768M Please let me know about ADR1 and ADR2 pin of TAS5768M. Are these pin have internal Pullup / Pulldown resister? If have internal resister, please let me know resister value (Min / Typ / Max). Best regards…
    • Resolved
    • over 9 years ago
    • Audio
    • Audio forum
  • Difference between TAS5760M and the TAS5768M?

    Adam Kiburz
    Adam Kiburz
    Other Parts Discussed in Thread: TAS5760M , TAS5768M Hi, What is the difference between TAS5760M and the TAS5768M? The specs are nearly the same with only minor differences. Thanks.
    • over 10 years ago
    • Audio
    • Audio forum
  • Answered
  • RE: TAS5768M Self clearing

    kyt
    kyt
    Resolved
    Hi,d2, I am sure DVDD is not going away momentarily in our test. But AVDD and CPVDD is off. Is it neceaary to source AVDD and CPVDD with DVDD due to hold register? The D/S describes that POR source is DVDD > 2.8 V. 8.4.2.1 Power-On Reset Function…
    • over 10 years ago
    • Audio
    • Audio forum
  • TAS5768M ,Unexpected mute after changong MCLK

    kyt
    kyt
    Other Parts Discussed in Thread: TAS5768M Hi, The stop of sound response has occurred after POR in our test. And it is recovered by configuring register again. It is the three following points to like to check. 1)What is the correct sequence to set…
    • over 10 years ago
    • Audio
    • Audio forum
  • About a gain setup of TAS5768M.

    Satoshi
    Satoshi
    TI Thinks Resolved
    Other Parts Discussed in Thread: TAS5768M Please let me know about a gain setup of TAS5768M. I think that Closed Loop AMP of datasheet figure 30 is fixed Gain, and inputs the calculation result of DSP into DAC, it carries out gain control. Is…
    • over 10 years ago
    • Audio
    • Audio forum
  • About DC protection of TAS5766M / TAS5768M

    Satoshi
    Satoshi
    TI Thinks Resolved
    Other Parts Discussed in Thread: TAS5768M About DC protection of TAS5768M, where is "Output DC voltage" in a device? And, what is looking at "Output DC voltage" ? I think that PVCC is seen with the comparator, is it right? Best regards, Sat…
    • over 11 years ago
    • Audio
    • Audio forum
  • Answered
  • TAS5768M RAM hold with power down mode

    kyt
    kyt
    Resolved
    Other Parts Discussed in Thread: TAS5768M Hi,ALL TAS5768M can got to power down mode by setting Page01,Regsiter0x02,bit0. It should be hold CRAM,IRAM,P0 and P1. If AVDD and CPVDD were OFF, RAM data is clear? It is occurred in our situation…
    • Resolved
    • over 10 years ago
    • Audio
    • Audio forum
  • TAS5768M speaker limitation register of output and amplitude

    kyt
    kyt
    Other Parts Discussed in Thread: TAS5768M , PUREPATHSTUDIO Hi, Now we are developing speaker with smart amp. TAS5768M can be set limitation of output and amplitude limitation to speaker. http://www.ti.com/product/tas5768m So,What register…
    • over 10 years ago
    • Audio
    • Audio forum
<>

Didn't find what you are looking for? Post a new question.

  • Ask a new question