• TCAN1043-Q1: Question about TCAN1043-Q1

  

  Jimmy Huang

  Part Number: TCAN1043-Q1 Other Parts Discussed in Thread: TCAN1043 , Tool/software: Hello： Does TI's TCAN1043 support first frame wake-up + identification? Thanks！！！

  • 7 days ago
  • Interface
  • Interface forum
Answered

• RE: TCAN1043-Q1: TCAN1043-Q1

  

  Eric Hackett

  Resolved

  Kkkkk, kkkkk ys said: 1. CAN bus bias = autonomous(does it mean not designated CAN bus voltage?) This means that the bus will be biased to GND unless there is CAN traffic. At that point, the CAN bus will be biased to 2.5V. kkkkk ys said: 2. WAKE…

  • 7 months ago
  • Interface
  • Interface forum

• TCAN1043-Q1: Will TCAN1043-Q1 support ISO11898-1?

  

  Wenting Wu

  TI Thinks Resolved

  Part Number: TCAN1043-Q1 Tool/software: Hello Expert, May I ask whether Will TCAN1043-Q1 support ISO11898-1? Best regards, Wenting

  • 11 months ago
  • Interface
  • Interface forum

• TCAN1043-Q1: nFault operation if don't used

  

  Beida Song

  TI Thinks Resolved

  Part Number: TCAN1043-Q1 Tool/software: Hi Expert, If the nFault is not used, how to deal nfault pin? floating? connect to GND or pull up to VCC? The device is TCAN1043-Q1.

  • 2 months ago
  • Interface
  • Interface forum
Answered

• TCAN1043-Q1: TCAN1043-Q1

  

  kkkkk ys

  Resolved

  Part Number: TCAN1043-Q1 Tool/software: Hi, I have a question about wake-up sequence of CAN transciever. 1. When the wake-up pattern comes into the transceiver through the busbar from the outside, the transceiver goes into the wake-up state and…

  • Resolved

  • 9 months ago
  • Interface
  • Interface forum

• TCAN1043-Q1: TCAN1043 wake up

  

  baoxiang wang

  TI Thinks Resolved

  Part Number: TCAN1043-Q1 Other Parts Discussed in Thread: TCAN1043 , Tool/software: Hi Ti team， Our actual application is similar to the recommended application below, but with the addition of a divider resistance between the INH and DC-DC EN pins.…

  • 7 months ago
  • Interface
  • Interface forum
Answered

• TCAN1043-Q1: Termination Resistor

  

  ABKD

  Resolved

  Part Number: TCAN1043-Q1 Tool/software: Hello, I am using TCAN1043-Q1 CAN transceiver, if there are 10 nodes on CAN bus with 120-ohm termination resistor at each node, then the equivalent resistance between CAN H and CAN L will be only 12 ohms. In…

  • Resolved

  • 4 months ago
  • Interface
  • Interface forum
Answered

• TCAN1043-Q1: nFault toggling

  

  Marcus Seeberger

  Resolved

  Part Number: TCAN1043-Q1 Other Parts Discussed in Thread: TCAN1043A-Q1 Tool/software: We see that the nFAULT pin toggles between 'low' (single wire error) and high (no single wire error) when CAN L is shorted to GND and chip is in NORMAL state. This behaviour…

  • Resolved

  • 2 months ago
  • Interface
  • Interface forum

• TCAN1043-Q1: VIO and VCC, VSUP internal circuit association

  

  Colin Chen

  TI Thinks Resolved

  Part Number: TCAN1043-Q1 Tool/software: Dear Experts, My customer is testing the voltage tolerance of VCC and VSUP and has found the following situations: When a voltage of 13V is applied to VCC alone, it will cause damage to the VCC and VIO pins, resulting…

  • 1 month ago
  • Interface
  • Interface forum

• TCAN1043A-Q1: Detailed difference between TCAN1043A-Q1 and TCAN1043-Q1

  

  Mostafa Askar

  TI Thinks Resolved

  Part Number: TCAN1043A-Q1 Other Parts Discussed in Thread: TCAN1043-Q1 , , TCAN1043HG-Q1 , TCAN1043N-Q1 , TCAN1043G-Q1 , TCAN1043 , TCAN1043H-Q1 Tool/software: Hi Expert, Can I get the detailed difference between TCAN1043A-Q1 and TCAN1043-Q1? Thanks…

  • 4 months ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.