• 

  Howard Zou

  • 2 months ago
  • Interface
  • Interface forum

  TCAN1051H: can we remove the terminate resistor for 2 CAN communication?

  TI Thinks Resolved

  Part Number: TCAN1051H Hi, my customer is using this device for board to board communication. The distance is just around 10cm. There are only 2 TCAN1051H in the system.
• 

  Frank Xiao

  • 3 months ago
  • Interface
  • Interface forum

  TCAN1051H: SPI to CAN device

  TI Thinks Resolved

  Part Number: TCAN1051H Hi team, My customer wants to find the solution to replace the mcp2518 which is a SPI to CAN device. Do you have some suggestions to recommend? Thanks.
• 

  Yuto Sakai

  • 6 months ago
  • Interface
  • Interface forum

  TCAN1051H: ESD Ratings

  TI Thinks Resolved

  Part Number: TCAN1051H Hi, Could you tell me about ESD Ratings? Is there an ESD Rating spec between CANH and CANL? Should I check “All terminals”? Best regards, Yuto Sakai
• 

  Eric Hackett

  • 5 months ago
  • Interface
  • Interface forum

  RE: TCAN1051V-Q1: Internal function to stop communication

  Hidekazu, There are several fault protection features integrated into the TCAN1051: Integrated ESD protection up to IEC standards Bus fault protection +/-58V for TCAN1051 and TCAN1051V, and +/- 70V for the TCAN1051H Undervoltage protection on...
• 

  Roy Chou1

  • 1 month ago
  • Interface
  • Interface forum

  TCAN1051H-Q1: When will we use the silent mode

  • Resolved

  Part Number: TCAN1051H -Q1 Hi Team, Could you let me know when will we use the silent mode(TCAN1051
• 

  John Fedak

  • over 2 years ago
  • Interface
  • Interface forum

  TCAN1051H: TVS Diode Recommendation for 60V Battery System

  • Resolved

  Part Number: TCAN1051H Hi Team, Good morning, do we have a TVS diode recommendation for CAN buses
• 

  John Fedak

  • over 2 years ago
  • Interface
  • Interface forum

  TCAN1051H: Confirming the S/STB leakage on the TCAN1042 and TCAN1051

  TI Thinks Resolved

  Part Number: TCAN1051H Hi Team, Good morning, can you confirm the leakage specs of the S/STB pin of the TCAN1051 (top ) and TCAN1042 (bottom) devices? The specs show tighter control of the leakage when the input level matches the level of where...
• 

  Kai Hsiao

  • over 3 years ago
  • Interface
  • Interface forum

  TCAN1051H: tidub36a document

  • Resolved

  Part Number: TCAN1051H Dear Sir I can't download TI design tidub36a on TI website ,could you kindly
• 

  Max Robertson

  • over 2 years ago
  • Interface
  • Interface forum

  RE: TCAN1051H: How to replace MCP2551

  Hi Kuo, MCP2551 supports a common mode range of +/- 12 V, although it is only compliant to the CAN standard across a +/- 7 V range. Either TCAN1042 or TCAN1051 would be good replacements as long as the slope control function is not needed. (I mention...
• 

  Kazuya Nakai59

  • over 3 years ago
  • Interface
  • Interface forum

  RE: TCAN1051 can meet IEC 61000-4-6 up to 10V

  Hi Michael, Thank you for your reply. Is there any document describes that TCAN1051H/HV/HGV/HG meet the requirements of International Electrotechnical Commission(IEC) 61000-4-6 up to 10 V except the following URL? newscenter.ti.com/2016-04-05-TI...

Didn't find what you are looking for? Post a new question.

• Ask a new question