• TCAN337: TCAN337 - Application Error - CAN Failure - Acknowledge Error

  

  Tirthraj Solanki

  TI Thinks Resolved

  Part Number: TCAN337 Hello, We are facing an intermittent CAN-FD issue in the field and would appreciate guidance from the community. Our system has two devices on the bus (no other device on the bus) using a request–response architecture. The master…

  • 9 months ago
  • Interface
  • Interface forum

• TCAN337: Fault pin

  

  Marvn Arcangel

  TI Thinks Resolved

  Part Number: TCAN337 Hi Experts, TCAN337D, there is Fault Pin (Pin Number 5). It is stated in datasheet as open drain output pin. We do not require that signal. So, just wanted to know if it is left open, will the whole transceiver work as intended…

  • 6 months ago
  • Interface
  • Interface forum
Answered

• TCAN337: CAN BUS Configuration

  

  Yannick DELMAS

  Resolved

  Part Number: TCAN337 Tool/software: Hello, I want to make a device with 21 nodes, all with a TCAN337. All are connected on a same CAN bus with 120 Ohms at the beginning and at the end of the bus. To you think this configuration is OK ? Best reg…

  • Resolved

  • over 1 year ago
  • Interface
  • Interface forum

• TCAN337: in combination with SN65HVD234DR

  

  Dennis vT

  TI Thinks Resolved

  Part Number: TCAN337 Tool/software: Hi, I would like to use the TCAN337 & SN65HVD234DR together in a same design. Seems that CAN protocol & electrical specification wise this is possible, but are there any other points to consider? Thanks in advance…

  • over 2 years ago
  • Interface
  • Interface forum

• TCAN337: 1M spec for bit width

  

  Brian Chan

  TI Thinks Resolved

  Part Number: TCAN337 Tool/software: Hi Team because the datasheet only show 2M and 5M spec. could you share the 1M spec? BRs Brian

  • over 2 years ago
  • Interface
  • Interface forum
Answered

• TCAN337: TCAN337 IC Failure and burned out

  

  Jit B

  Resolved

  Part Number: TCAN337 HI, I am using TCAN337 to connect upto 7 CAN nodes in a network for automotive application. I have dual CAN configuration, where CAN1 has 5 nodes and CAN 2 has 4 nodes. The circuit includes split termination (two 60 Ohms along with…

  • Resolved

  • over 4 years ago
  • Interface
  • Interface forum
Answered

• TCAN337: Mixed 3.3V and 5V CAN transceiver problems

  

  Jasper van der Graaf

  Resolved

  Part Number: TCAN337 Hi, My system uses a TCAN337 and needs to communicate with a 5V CAN chip MCP2561. According to the datasheets this should be possible because of the voltage difference in dominant and recessive state. Only I do not receive any data…

  • Resolved

  • over 3 years ago
  • Interface
  • Interface forum

• TCAN337: vs TCAN337G

  

  Needhu Gunasegaran

  TI Thinks Resolved

  Part Number: TCAN337 Dear Danny, as a follow up to https://e2e.ti.com/support/interface-group/interface/f/interface-forum/1116988/tcan337-and-tcan337g-technical-question-and-device-marking/4140016#4140016 , are there any difference to EMC performance…

  • over 4 years ago
  • Interface
  • Interface forum
Answered

• TCAN337: and TCAN337G Technical Question and device marking

  

  Needhu Gunasegaran

  Resolved

  Part Number: TCAN337 Dear Team, My customer needed some clarification on below queries from your end. TCAN332GDCNT can support higher Signaling rate. Please confirm TCAN332GDCNT can be downward compatible with Signaling rate lower than 1Mbps? …

  • Resolved

  • over 4 years ago
  • Interface
  • Interface forum

• TCAN337: Could the pin5 and pin8 be tied to GND?

  

  Gordon Xu

  Answer Suggested

  Part Number: TCAN337 Other Parts Discussed in Thread: TCAN330 , TCAN334 Hi experts, Could the pin5 and pin8 of TCAN330/2/4/7 be tied to GND? BR, Gordon

  • over 4 years ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.