Filter by Reset

All
Forums (587)
  • Processors (562)
  • Power management (17)
  • Interface (6)
  • Arm-based microcontrolle... (2)
  • View all
Technical Articles (3)
Wikis (0)
Files (0)
Groups (0)
FAQ
  • Show only FAQs
Reply
  • Resolved
  • TI thinks resolved
  • Answer suggested
  • Has replies by TI employees
  • Has replies
Creation Date
  • Any
  • Past Week
  • Past Month
  • Past 3 Months
  • Past 6 Months
  • Past Year
From
To


Search tips
Showing 587 results View by: Thread Post Sort by

  • TDA4AL-Q1: How to build csirxtx_loopback_test in pdk_j721s2_10_00_00_27?

    TI Thinks Resolved
    Part Number: TDA4AL-Q1 Tool/software: Hi TI Expert, I need to build csirxtx_loopback_test to test CSIRX bypassing data to CSITX function, but I have no idea how to build it. Could you give me the command and where can I locate the built binary after a…

  • TDA4AL-Q1: [TDA4AL] dp83tg721 link detected is always no

    Part Number: TDA4AL-Q1 Tool/software: Hi Sir, We use dp83tg721. When I plug and unplug T1, I see that link detected is always no. Is this related to rgmii tx/rx delay? Or other parts need to be adjusted? Thanks?

  • TDA4AL-Q1: TDA4AL-Q1: How to increase DFU receiver buffer

    Part Number: TDA4AL-Q1 Tool/software: Hi Sir, When we download SW 800MB by using DFU mode, we can't complete the download, SW downloading always be interrupted randomly 30% or 70%. Can we increase DFU receiver buffer to avoid the issue? Or do you…

  • TDA4AL-Q1: How can I start up a CSI2 camera directly on i2c-5 on on TDA4AL-Q1 EVM?

    Part Number: TDA4AL-Q1 Other Parts Discussed in Thread: TCA6408 Tool/software: Hi, TI expert, I set the camera device camera@6c in main_i2c5, but the i2c always not be detected by linux tool of i2cdetect command. Please help to check why i2c-5 not can…

  • TDA4AL-Q1: timeout in ti_sci_recv_message()

    Part Number: TDA4AL-Q1 Tool/software: Hello Experts I've noticed below error message sometimes while testing our HW. "ti_sci_recv_message, unable to receive message\n" <psdkqa/qnx/bsp/src/hardware/startup/boards/j721s2/lti_sci.c>…

  • RE: TDA4AL-Q1: TDA4AL DDR

    Hi, Gaston yan said: Is there any relationship between the value DDRSS_PLL_FHS_CNT and training? Does the size of this value affect the training time? A larger DDRSS_PLL_FHS_CNT value implies more ranks / "frequency sets" are enabled. Thus, more training…

  • TDA4AL-Q1: Is TDA4AL HS key burn via SD card only

    Part Number: TDA4AL-Q1 Tool/software: Hi TI expert， Can the TDA4AL HS KEY only be burned through SD card? Can it be burned via USB or UART of the main domain, or other interface? Best Regards Juanli Zhang

  • TDA4AL-Q1: [TDA4AL] How to create a MCU_CPSW for PHY DP83TG721x-Q1?

    TI Thinks Resolved
    Part Number: TDA4AL-Q1 Tool/software: Hi Sir, PHY DP83TG721x-Q1 is connected to MCU_RGMII1_XX in our product. How to create a MCU_CPSW for DP83TG721x-Q1 in the A72 u-boot and linux ? We can NOT find MCU_CPSW after executing mdio list in the A72 u-boot. …

  • TDA4AL-Q1: Info Needed on VISS shceduling

    TI Thinks Resolved
    Part Number: TDA4AL-Q1 Tool/software: Hi Gang Hua , We are referring TRM. We encountered below section about VISS configuration. Want to know , 1.What is line mode and frame mode of viss? 2. What is horizontal and vertical blanking? 3. What is 'HzLatencyLine…
    • Answered

  • TDA4AL-Q1: Comment in tivxMem.TranslateAddrMalloc

    Resolved
    Part Number: TDA4AL-Q1 Tool/software: Hello Support-Team, I found the following comment in the tivxMem.TranslateAddrMalloc test: /* Check address translation. The translation should fail since the memory * has not been allocated using ether tivxMemAlloc…
    • Resolved
1 2 3 4 5 »

Didn't find what you are looking for? Post a new question.