Search tips
Showing 20 results View by: Thread Post Sort by

  • TDA4VP-Q1: NAND Flash

    TI Thinks Resolved
    Part Number: TDA4VP-Q1 Other Parts Discussed in Thread: J784S4XEVM Hi Team, Do we support Winbond NAND Flash? If yes, do we have specific components we tested? Thanks
    • Answered

  • TDA4VP-Q1: DRAM Support

    Resolved
    Part Number: TDA4VP-Q1 Hi Team, Can TDA4 support 2x 2GB DRAM? Also, in general - can it support 3x DRAM instead of 2x DRAM? Thanks.
    • Resolved

  • TDA4VP-Q1: CPSW9G access from MCU domain

    Part Number: TDA4VP-Q1 Dear support, We wish to know whether the CPSW9G (which resides within the Main domain) can be accessed from the MCU domain, and what are the provisions we should take care of, in both HW and SW, to acheive that. Two use-cases are…

  • TDA4VP-Q1: TDA4VP+PDN-3A & DRA829 +PDN-0C failure analysis in case of different power sequence errors

    Part Number: TDA4VP-Q1 Other Parts Discussed in Thread: DRA829 Dear TI Team, Currently I'm trying to perform the failure analysis of following 2 system solutions: 1. TDA4VP+PDN-3A 2. DRA829 +PDN-0C Due to the power sequence error may lead to damage…
    • Answered

  • TDA4VP-Q1: 3 different displays with each 4K @ 30fps possible?

    Resolved
    Part Number: TDA4VP-Q1 Dear Champs, Could you please let me know what is the maximum display resolution in TDA4VP-Q1? Is it possible display 3 different videos at each 4K @ 30fps possible? From TRM, I found below and it looks the total maximum resolution…
    • Resolved

  • TDA4VP-Q1: spi

    Part Number: TDA4VP-Q1 3、SPI当前SDK默认的通信速率是多少，通信速率可调范围是多少； What is the default communication rate of the current SDK of SPI, and what is the adjustable range of communication rate;

  • TDA4VP-Q1: serdes

    Part Number: TDA4VP-Q1 Other Parts Discussed in Thread: TDA4VH 2、当前TDA4VH使用了Serdes1（SGMII1~4）与Serdes0（PCIE1），能否通过pin to pin替换至TDA4VMP； At present, TDA4VH uses Serdes1 (SGMII1~4) and Serdes0 (PCIE1), whether it can be replaced by TDA4VMP through pin to…

  • TDA4VP-Q1: Can SPI interface be connected to SPI flash memory?

    TI Thinks Resolved
    Part Number: TDA4VP-Q1 Hi Expert, Can we use the SPI (not OSPI/QSPI) to connect to SPI flash memory? This memory don't need to store the bootloader, just is used as a memory. Is this supported in both Hardware and Software? Thanks. Best regards…

  • TDA4VP-Q1: Whether does ARM Compiler of TDA4VMP have TOOL confidence report or ISO26262 assessment report

    TI Thinks Resolved
    Part Number: TDA4VP-Q1 Hello, we plan to use TI compiler to develop software, as the peoject has fuction safety requirement， so we want to know whether ARM Compiler of TDA4VMP hasTOOL confidence report or ISO26262 assessment report. the ARM compiler…

  • TDA4VP-Q1: SPI/UART

    Part Number: TDA4VP-Q1 4、SPI的CS脚在配置软件中一般是有四根（CS0、CS1、CS2、CS3），一般而言我们只需要使用其中一根或者两根即可，那剩余的CS片选信号PIN脚如果配置成其他功能，是否会引起功能管脚冲突；Uart的流控信号（RTS、CTS）也有同样的问题，当我使用UART接口时，但是我不需要使用流控信号，对应的流控信号管脚可否配置为其他的功能管脚； SPI's CS pins generally have four in the configuration software…

Didn't find what you are looking for? Post a new question.