Answered

• THVD1424: THVD1424

  

  Cedric Tornesi

  Resolved

  Part Number: THVD1424 Tool/software: Dear TI support team, I use your THVD1424 for a New Space MRO Project. I use it in full-duplex, therefore the satellite customer load will be about 100 Ohms, even 120 Ohms as it is point to point connection, only…

  • Resolved

  • 21 days ago
  • Interface
  • Interface forum

• THVD1424: THVD1424 roadmap question

  

  Dane Zhang

  Part Number: THVD1424 Tool/software: Hi team， do we have recommendation for below application request? 1PPS+ToD interface RS422 level conversion for L3 Switch; Support 1 channel RS422 transceiver (i.e. 2 channels RS485); Or support 2 channels RS422 transceiver…

  • 4 months ago
  • Interface
  • Interface forum

• THVD1424: Wettable Flank for THVD1424

  

  ?? ??

  TI Thinks Resolved

  Part Number: THVD1424 Tool/software: Is there wettable flank PKG for THVD1424RGTR? If it has already supported, it would be helpful if you could also let me know.

  • 4 months ago
  • Interface
  • Interface forum
Answered

• THVD1424: Cable length vs. Data rate

  

  Atsushi Takahashi

  Resolved

  Part Number: THVD1424 Other Parts Discussed in Thread: SN65HVD22 Tool/software: Hi Team, I have a question about SLLA628. https://www.ti.com/lit/an/slla628/slla628.pdf There exists a tradeoff between speed and maximum bus length. If 5% jitter is acceptable…

  • Resolved

  • 4 months ago
  • Interface
  • Interface forum

• THVD1424: In half-duplex mode, do pins A and B connect to pins Y and Z internally?

  

  Wilson Wang

  TI Thinks Resolved

  Part Number: THVD1424 Tool/software: If the THVD1424 works in half-duplex mode, are pins Y and A, as well as Z and B, connected together internally? I cannot find any description in the datasheet. The reason I ask this question is that I need to utilize…

  • 3 months ago
  • Interface
  • Interface forum

• THVD1424: Is a pull-up needed for Line A? Will it cause problems if the VDD of the two devices is different?

  

  Wilson Wang

  TI Thinks Resolved

  Part Number: THVD1424 Tool/software: Let's consider the half-duplex mode only. Some people say the A line needs to be pulled up to VDD through a resistor, and the B line needs to be pulled down to GND through a resistor. However, I have a question…

  • 2 months ago
  • Interface
  • Interface forum

• THVD1424EVM: THVD1424

  

  Harsha K

  TI Thinks Resolved

  Part Number: THVD1424EVM Other Parts Discussed in Thread: THVD1424 , Tool/software: We are using the THVD1424 RS-485 receiver in the design and hence please share the Altium design files for the THVD1424EVM Evaluation Module for maintaining the same layout…

  • 6 months ago
  • Interface
  • Interface forum

• THVD1424: THVD1424

  

  Nitin Panchal

  Part Number: THVD1424 How to implement a circuit to pass transient level of 310V/300A. What is the internal resistance of H/F pin of this device?

  • 10 months ago
  • Interface
  • Interface forum
Answered

• THVD1424: Is this component compatible with RS-422?

  

  Mehmet Akkurt

  Resolved

  Part Number: THVD1424 Tool/software: Hello I need an RS-422 IC that I can switch between full duplex and half duplex I found the "THVD1424" IC but officially, there is no source that this IC can work with the RS-422 protocol. Can I use this IC for RS…

  • Resolved

  • 6 months ago
  • Interface
  • Interface forum
Answered

• THVD1424: ibis model for THVD1424

  

  Brendan Toy

  Resolved

  Part Number: THVD1424 Other Parts Discussed in Thread: THVD1400 Hi, is there an ibis model for THVD1424? If not, is there a good placeholder part that can be used in the meantime? Thanks, Brendan

  • Resolved

  • over 1 year ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.