Answered

• TLIN1024A-Q1: Not able to set Enable pin

  

  Narmatha T

  Resolved

  Part Number: TLIN1024A-Q1 Tool/software: Hello team, During tests with the TLIN1024A device, we are giving the Vsup as 12 V. From the data sheet it is mentioned as 3.3V - 5V for EN pin. We are giving the the 5V from the power supply to the EN pin…

  • Resolved

  • 8 months ago
  • Interface
  • Interface forum

• TLIN1024A-Q1: TLIN1021A-Q1: Input Capacitance of TXD pin

  

  Kento Sato

  TI Thinks Resolved

  Part Number: TLIN1024A-Q1 Tool/software: Hi team, I have a question on TLIN1024ARGYRQ1 and TLIN1021ADDFRQ1. I'd like to know input capacitance(pF) of TXD pin of each device but I can't find it. Could you please share it for each? Best regards…

  • over 1 year ago
  • Interface
  • Interface forum

• TLIN1024A-Q1: Tstg

  

  Kento Sato

  TI Thinks Resolved

  Part Number: TLIN1024A-Q1 Tool/software: Hi team, Could you provide storage condition spec "Tstg" for TLIN1024ARGYRQ1? The spec is not stated in Datasheet. Regards, Kento

  • over 1 year ago
  • Interface
  • Interface forum
Answered

• TLIN1024A-Q1: question about VSUP and responder/commander

  

  Jay wang

  Resolved

  Part Number: TLIN1024A-Q1 hi expert Q1: if responder LIN VSUP is 7V, commander LIN VSUP is 12V, whether is it ok? Q2:as we know, if LIN work as commander node, LIN bus need pullup resistor to power source. must this power source be same the VSUP?…

  • Resolved

  • over 2 years ago
  • Interface
  • Interface forum
Answered

• TLIN1024A-Q1: About ISUP(in SLEEP mode) max value at 25 ℃

  

  Y.Fukaya

  Resolved

  Part Number: TLIN1024A-Q1 The max current including -45℃ and 125℃ temperature conditions is set at 20uA. (Vsup ≦ 14V) Does the max current tend to decrease if only 25°C conditions? *The answer as a reference value (technical opinion) is fine.

  • over 2 years ago
  • Interface
  • Interface forum
Answered

• TLIN1024A-Q1: 2CH vs. 4CH Schematic

  

  Tom Lynskey

  Resolved

  Part Number: TLIN1024A-Q1 Other Parts Discussed in Thread: TLIN1024-Q1 Hi, My customer has a TLIN1024A-Q1 question. In 'high content' vehicles they use all the channels but on the 'low content' vehicles they only use two. What changes would need to…

  • Resolved

  • over 3 years ago
  • Interface
  • Interface forum

• TLIN1024A-Q1: How about use less than 4 LINs?

  

  Yuan Tan63

  TI Thinks Resolved

  Part Number: TLIN1024A-Q1 Hi, For example, if we want to let LIN1 unused, can customer let EN1/ RXD1/TXD1 floating? Thank you B&R Yuan Tan

  • over 2 years ago
  • Interface
  • Interface forum

• TLIN1024A-Q1: TLIN1024

  

  Manoj Agarwal

  TI Thinks Resolved

  Part Number: TLIN1024A-Q1 Other Parts Discussed in Thread: TLIN1021A-Q1 , TLIN1028-Q1 Hi team, Any solution to have INH output for Device TLIN1024. I checked NXP device SJA1124 is having thta so replacement of SJA1124 will also work. We are doing…

  • over 3 years ago
  • Interface
  • Interface forum
Answered

• TLIN1024A-Q1: Vsup1/2 datasheet inconsistencies

  

  Jonathan Jank

  Resolved

  Part Number: TLIN1024A-Q1 The proper connection of Vsup1/2 is confusing as the datasheet shows multiple ways to do that. The connections for the pullups for commander mode are also not clear. - Figure 9-1 and Figure 12-1 show that Vsup1 and Vsup2…

  • Resolved

  • over 3 years ago
  • Interface
  • Interface forum

• TLIN1024A-Q1: Design Concern

  

  Muwei Zheng

  TI Thinks Resolved

  Part Number: TLIN1024A-Q1 Other Parts Discussed in Thread: TLIN1021A-Q1 Hi team, I have two questions on TLIN1021A-Q1&TLIN1024A-Q1 in design: 1. Can we leave LINx pin float if it is not used? 2. Can we put two 220nF cap in series near the Vsup pin…

  • over 3 years ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.