Search tips
Showing 15 results View by: Thread Post Sort by

  • TLIN1431-Q1: TLIN1431-Q1

    TI Thinks Resolved
    Part Number: TLIN1431-Q1 i have question about total sleep current of this device. the vbat and wake pin sleep current data can't be found in datasheet. see below:

  • TLIN1431-Q1: TLIN1431-Q1 in Standby Mode

    TI Thinks Resolved
    Part Number: TLIN1431-Q1 In TLIN1431-Q1 Standby Mode:VCC: on nRST: high,I want to confirm we LIN bus on. Can LIN BUS WAKEUP by PIN “ RXD ”? we need RXD give a Falling edge triggered to MCU in Standby Mode.

  • TLIN1431-Q1: Does LIN pin have an internal clamp

    TI Thinks Resolved
    Part Number: TLIN1431-Q1 Hello. I'm wondering if the LIN pin follows the VSUP supply voltage, or is there a clamping diode internally that limits the voltage on it? If 24V is put on the VSUP pin would we expect about 24V on the LIN pin as well? …
    • Answered

  • TLIN1431-Q1: TLIN14315RGYRQ1

    Resolved
    Part Number: TLIN1431-Q1 Other Parts Discussed in Thread: TLIN1431EVM , In pin mode, HSS pin is controlled by HSSC pin. the datasheet does not specify HSSC = High or Low to turn on HSS pin output. does the below description indicates that HSSC = LOW will…
    • Resolved
    • Answered

  • TLIN1431-Q1: TLIN14315RGYRQ1

    Resolved
    Part Number: TLIN1431-Q1 we'll design SBC TLIN14315RGYRQ1 to a pin control mode. i have question as below: 1. is nWDR an open drain output for pin mode configuration? 2. in general, we will connect NRST to reset microcontroller during UV and power…
    • Resolved
    • Answered

  • TLIN1431-Q1: why external LDO is used in channel expansion examples

    Resolved
    Part Number: TLIN1431-Q1 Hi team, We found in all the channel expansion examples, 3.3V external LDO is used. We want to know why. Why 3.3 LDO output of TLIN1431 isn't used to supply MCU VDD?
    • Resolved
    • Answered

  • TLIN1431-Q1: can we provide separate VCC to microcontroller and not use VCC from SBC chip

    Resolved
    Part Number: TLIN1431-Q1 HI team, I am intent to provide separate power rails to Microcontroller ( 3.3V) and not using TLIN1431-Q1 VCC power rail from internal regulator. I am confuse here, because in application Microcontroller VCC is connected with…
    • Resolved

  • TLIN1431-Q1: TLIN14315RGYRQ1 detailed package description document

    TI Thinks Resolved
    Part Number: TLIN1431-Q1 Hi Expert, Would you mind sharing with me the detailed package description document? The datasheet doesn’t include detail dimension for footprint. Thanks a lot for your warm help!

  • RE: TLIN1431-Q1: HSS pin can withstand short to GND/battery?

    Hi Ben, Seems like we are on the same page. Ben King said: The HSSC pin can just be viewed as an enable pin for the HSS right? Yes, the HSSC controls the HSS as you mentioned while in Standby, Normal, or Fast modes. Ben King said: Also, what happens if…

  • RE: TLIN1441-Q1: wake up in standby mode

    Hi Eric, Please help check internally if there have any workarounds. It may have risks in customer's project. And I am confused that the behavior of TLIN1028-Q1 in standby mode is different with TLIN1441-Q1. TLIN1028-Q1 is fully match with customer…

Didn't find what you are looking for? Post a new question.