Answered

• TMP101-Q1: ALERT pin left NC

  

  Caroline Cadena

  Resolved

  Part Number: TMP101-Q1 Other Parts Discussed in Thread: TMP101 Tool/software: In the TMP101-Q1 datasheet, it is recommended that the ALERT pin is paired with a pull-up resistor. I'm choosing not to use the ALERT pin, as I'm only using the unit for data…

  • Resolved

  • 4 days ago
  • Sensors
  • Sensors forum

• TMP101: TMP101 Interface?

  

  Maksym Kloka

  TI Thinks Resolved

  Part Number: TMP101 Tool/software: Hello, is there a development kit ... and/or a good set of instructions for interfacing with TMP101NA temperature sensors? Sincerely, Maksym

  • 2 months ago
  • Sensors
  • Sensors forum

• TMP101: TMP101NA/250G4 Alert pin can be pull up with 1.8V or not?

  

  Sagar Kumar

  TI Thinks Resolved

  Part Number: TMP101 Other Parts Discussed in Thread: TMP118 , TMP102 , TMP110 , TMP1075 Tool/software: Hi, I am using TMP101NA/250G4 in my design , just want to know can we pull up alert with 1.8V since my processor IO level is 1.8V? But TMP101NA/250G4 V…

  • 1 month ago
  • Sensors
  • Sensors forum
Answered

• TMP101: oscillator

  

  Roee Kimchi

  Resolved

  Part Number: TMP101 at the block diagram I see that this device has an OSC block. is it connected to the SCL line or is there an internal oscillator? thanks you!

  • Resolved

  • over 2 years ago
  • Sensors
  • Sensors forum
Answered

• TMP101-Q1: Pull-up for address line.

  

  Srilakshmi DV

  Resolved

  Part Number: TMP101-Q1 Hello team, As per the datasheet, a pull-up resistor is not recommended on address pin(ADD0). For my application, it is required to place a pull-up resistor. Is it okay to do so? In that case, may I know if there is recommended…

  • Resolved

  • over 2 years ago
  • Sensors
  • Sensors forum
Answered

• TMP101-Q1: Confirmation Inquiry

  

  Renan Santos Adriano

  Resolved

  Part Number: TMP101-Q1 Hello Team, My customer wanted to know if the device TMP101NAQDBVRQ1 still meets the concept of 8541 semiconductor based transducer. Thanks in advance. Regards, Renan

  • Resolved

  • over 3 years ago
  • Sensors
  • Sensors forum

• TMP101-Q1: what is the default value of the configuraiton register after power up ???

  

  Roman Manka

  TI Thinks Resolved

  Part Number: TMP101-Q1 Other Parts Discussed in Thread: TMP100-Q1 , spec only specifies POL bit default value after power up, I need to know other bits too: SD ? TM ? (don't have the part on hand just to read it)

  • over 2 years ago
  • Sensors
  • Sensors forum
Answered

• TMP101: Handling Alert Pins

  

  Ryu Yamashita

  Resolved

  Part Number: TMP101 Other Parts Discussed in Thread: TMP100 Hi team, I am using TMP101 instead of TMP100 to increase availability, but I do not need the alert pin. In this case, how should I handle the alert pin? Sincerely. Ryu.

  • Resolved

  • over 3 years ago
  • Sensors
  • Sensors forum

• TMP101: TMP101 Register

  

  Raymond He

  TI Thinks Resolved

  Part Number: TMP101 According to datasheet, TMP101 has 5 registers, which are Pointer Register, Temperature Register and Configuration Register, TLOWRegister and THIGHRegister.The Pointer Register is configured to identify which Register to read and write…

  • over 4 years ago
  • Sensors
  • Sensors forum

• TMP101: Does TMP101 sense the temperature of the pin or of the ambience?

  

  Wayne Wang20

  TI Thinks Resolved

  Part Number: TMP101 Hi team, I want to check with you that does TMP101 sense the temperature of the pin or of the ambience? In the datasheet, it claims as below My understanding is that the GND pin is the primary path to conduct the temperature of the…

  • over 4 years ago
  • Sensors
  • Sensors forum

Didn't find what you are looking for? Post a new question.