• 

  Andy Robles

  • 2 months ago
  • Interface
  • Interface forum

  RE: TPD2E2U06: TPD2E2U06DRLR

  Hi Hanh, The layout looks correct. One signal line is using the IO protection channel provided from PIN 3 and the other from PIN5. Looks good. Best regards, Andy Robles
• 

  Jared Becker

  • 4 months ago
  • Interface
  • Interface forum

  Over voltage clamp on data lines

  • Resolved

  - for USB) from a potential short to to up to 18V. I was thinking a device like the TPD2E2U06 might work
• 

  Moshe Avidan

  • 11 months ago
  • Interface
  • Interface forum

  TPD2E2U06: TPD2E2U06DRLR

  TI Thinks Resolved

  Part Number: TPD2E2U06 Hi, what is its maximum clamping voltage of the TPD2E2U06? Data sheet DC table is stating low voltage for clamping , but it's looks like 60V according to the ESD graph on the datasheet Thanks Moshe
• 

  Kevin Allen18

  • 8 days ago
  • Interface
  • Interface forum

  RE: SN65LVDM050: Line Drive IC for Fast Serial Interface using TMS320F28388D

  Hi Dushyant, Amtech So for this application if we go with DSLVDS1047PWR then we will need 2 driver ICs, And if we go with SN65LVDM50PW then we will need only 1 driver IC. Due to this reason we have selected SN65LVDM50PW Driver IC. You would...
• 

  Cedrick Jimenez

  • over 1 year ago
  • Interface
  • Interface forum

  TPD2E2U06: Difference between TPD2E2U06DRLR-P and TPD2E2U06DRLR

  • Resolved

  Part Number: TPD2E2U06 Hi, Good day! Our customer wants to know the difference between
• 

  Cody Watkins

  • 2 months ago
  • C2000™ microcontrollers
  • C2000™ microcontrollers forum

  RE: TMS320F28069M: Which Isolator IC to use for interfacing "USB" with "Launchpad" using "D+" & "D-" pinout.

  Mihir, https://www.ti.com/lit/sszb130 The document above recommends a number of ESD solutions for USB on Page 5. TPD1E05U06 and TPD2E2U06 are 2 of the recommended solutions. If you need more info on these products we can move this thread over...
• 

  Kumaran Anand Balasubramanian

  • 6 months ago
  • Interface
  • Interface forum

  TPD2E2U06-Q1: RS232 does not work with TPD2E2U06-Q1

  • Resolved

  Part Number: TPD2E2U06 -Q1 Hi, we were using TPD2E007 ESD diodes to protect our RS232 lines. We
• 

  Koji Hayashi92

  • 2 months ago
  • Interface
  • Interface forum

  TPD2E2U06-Q1: IEEE 100BASE-T1

  Part Number: TPD2E2U06-Q1 Hi TI-team My customer has a question. They think this part is a diode that can be used in Ethernet for vehicles. Is the following satisfied ? - OPEN ALLIANCE：IEEE 100BASE-T1 EMC Test Specification for ESD suppression...
• 

  Oba

  • over 2 years ago
  • Interface
  • Interface forum

  TPD2E2U06: Best selection for USB2.0 FS

  • Resolved

  Part Number: TPD2E2U06 Hello, I am looking for ESD protection for USB2.0 FS. But each selection
• 

  Cameron Phillips

  • 6 months ago
  • Interface
  • Interface forum

  RE: TPD2EUSB30: Part recommendation please

  Hello, Yes the TPD2E2U06 could also work as the signal speed is not very high. Unidirectional devices or bidirectional devices can be used on unidirectional signals. My point is that ESDS304 is our lowest clamping family of the devices that would...

Didn't find what you are looking for? Post a new question.

• Ask a new question