• 

  Joe Vasquez

  • over 1 year ago
  • Interface
  • Interface forum

  TPD2EUSB30A: Recommended stencil design for small SOT

  • Resolved

  Part Number: TPD2EUSB30A We are having issues with soldering TPD2EUSB30ADRTR. We are a custom
• 

  Donald Schelle90399

  • over 1 year ago
  • Interface
  • Interface forum

  TPD2EUSB30A: Suitable for Ethernet Interface

  • Resolved

  Part Number: TPD2EUSB30A Hello, We need to protect a 10/100 ethernet interface. At present
• 

  Gabriel Garza45

  • over 2 years ago
  • Interface
  • Interface forum

  TPD2EUSB30A: TPD2EUSB30ADRTR - Need Tape and Reel Tolerance

  Part Number: TPD2EUSB30A Hello, We have a customer who is asking for the Tape and Reel tolerance for this device. There is no reference to any tolerance, only "Nominal". Is there anything we can provide? "I can't find the tolerance...
• 

  Cameron Phillips

  • over 2 years ago
  • Interface
  • Interface forum

  RE: WEBENCH® Tools/TPD2EUSB30A: TPD2EUSB30A Footprint recommendation

  Hello, I would use the stencil drawing from the datasheet. However both of them will work. Regards, Cameron
• 

  George Ioakimedes

  • over 1 year ago
  • Interface
  • Interface forum

  TPD2EUSB30A: Compared to TPD2E001

  • Resolved

  Part Number: TPD2EUSB30A I have an old design with a USB charger and we used the TPD2EUSB30A
• 

  circuitrees

  • over 1 year ago
  • Interface
  • Interface forum

  USB2.0 High Speed acceptable use?

  • Resolved

  Part Number: TPD2EUSB30 I see in the 'Layout Examples' in the Datasheet http://www.ti.com/lit/ds/symlink/tpd2eusb30a.pdf for the TPD2EUSB30 that I can use the TPD2EUSB30ADRTR for USB 2.0 lines, however nowhere in any documentation can I find that it is acceptable and specified as okay for use...
• 

  Garrick88

  • over 2 years ago
  • Interface
  • Interface forum

  RE: TUSB8041: TUSB8041 Schematic Review - Very simple implementation

  Hi Jorge, I've attached an updated schematic here with your changes. In layout, I assume the coupling caps on the SS TX lines go as close to the USB connectors, as possible but just behind the DLP11SN900HL2L chokes and TPD2EUSB30A? Thanks, Garrick...
• 

  Max Robertson

  • over 5 years ago
  • Interface
  • Interface forum

  RE: LVDS Repeater input failures

  Joe, I don't have any first-hand experience with using TVS diodes with LVDS transceivers, but just browsing around available options it looks like TPD2EUSB30A could be a good fit: http://www.ti.com/product/tpd2eusb30a It's marketed specifically...
• 

  gangu.C

  • over 6 years ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum

  RE: IBIS models

  Hi David, Thanks for the reply. Please share the IBIS models for TPS devices quickly. For TPD device, i'll take the TPD2EUSB30A device data. Regards, Gang
• 

  eli

  • over 4 years ago
  • Interface
  • Interface forum

  UART PROTECTION

  I want to protect my uart RX,TX lines. I found TPD2EUSB30A. which is for differential lines. Basically, it’s just a TVS diodes, so it shouldn’t care if the lines are single-ended or differential. Am I right ?

Didn't find what you are looking for? Post a new question.

• Ask a new question