• TPS3710: TPS3710QDSERQ1 - Handling documents

  

  Nandha T

  TI Thinks Resolved

  Part Number: TPS3710 Hi, Is there any documentation available regarding cleaning procedures for this part specifically whether isopropyl alcohol (IPA) should or should not be used? Thanks, Nandha T

  • 3 months ago
  • Power management
  • Power management forum

• TPS3710: TPS3710QDSERQ1- Soldering Profile and Baking Details

  

  Nandha T

  TI Thinks Resolved

  Part Number: TPS3710 Hi, Could you please share the details regarding Soldering profile and baking for this part TPS3710QDSERQ1 Thanks, Nandha T

  • 4 months ago
  • Logic
  • Logic forum

• TPS3710:o

  

  masamui fukuda

  Part Number: TPS3710 Tool/software: Hello I would like to ask about TPS3710DDCT. Pin numbers 2, 4 and 6 of this IC I think it is GND, but when I checked the continuity only with IC before mounting, GND was not connected to each other. Is there any problem…

  • over 1 year ago
  • Power management
  • Power management forum

• TPS3710: more fast propagation delay time

  

  Lawrence He

  TI Thinks Resolved

  Part Number: TPS3710 Other Parts Discussed in Thread: TPS3842 Tool/software: Hi, Support Team do we have same function with TPS3710, but more fast propagation delay time parts? if any suggestion, Please advise me. Thanks, Best regards, …

  • over 1 year ago
  • Power management
  • Power management forum
Answered

• TPS3710: Request to Functional safety FIT value and Failure Mode Distribution, Gate scale that meet Siemens standard SN29500

  

  Sijia Zhu

  Resolved

  Part Number: TPS3710 Other Parts Discussed in Thread: AM2434 , Tool/software: I would like to have some help with the Failure Mode Distribution for the following part number TPS3700DDCR , this is usually included in the Functional Safety FIT Rate, FMD…

  • Resolved

  • 10 months ago
  • Power management
  • Power management forum
Answered

• TPS3710: Voltage at OUT pin when VDD is 0V

  

  Kei Kuwahara

  Resolved

  Part Number: TPS3710 Hello team, I just want to check if I can input voltage up to 18V at OUT pin when VDD is OFF? Best Regards, Kei Kuwahara

  • Resolved

  • over 1 year ago
  • Power management
  • Power management forum
Answered

• TPS3710: Definition of VHI and IO

  

  Kei Kuwahara

  Resolved

  Part Number: TPS3710 Hello team, What is the definition of VHI and IO from the equation(2)? Also is VPU = Pull up voltage? Best Regards, Kei Kuwahara

  • Resolved

  • over 2 years ago
  • Power management
  • Power management forum
Answered

• TPS3710:Check the meaning of the expression "0.1-uF" in the datasheet.

  

  user1866475

  Resolved

  Part Number: TPS3710 Hello, The expression "0.1-uF" is used in Datasheet "8.3 Do's and Don'ts". What is this expression? Does it mean a value smaller than 0.1uF? Best Regards, Yukio Oyama

  • Resolved

  • over 2 years ago
  • Power management
  • Power management forum
Answered

• TPS3710: Start-up delay

  

  K.Yaita

  Resolved

  Part Number: TPS3710 Hi Team, The datasheet shows >(2) During power on, VDD must exceed 1.8 V for at least 150 µs before the output is in a correct state. I believe "1.8V" is typo and 0.8V is correct because V(POR) is 0.8V(max). Is my understanding correct…

  • Resolved

  • over 3 years ago
  • Power management
  • Power management forum

• TPS3710: RP Value

  

  Marvn Arcangel

  TI Thinks Resolved

  Part Number: TPS3710 Hi Team, Can you confirm if the value calculated for RP is correct? VPU - 3.3V Detection voltage - 3.3V (sense pin) OUT is connected to Hi-Z (FPGA input) OUT (Output sink current) - 40mA => RP =10 kohm (33uA) Additional…

  • over 3 years ago
  • Power management
  • Power management forum

Didn't find what you are looking for? Post a new question.