Answered

• TPS62861: TPS628610YCHR : Output Voltage Issue

  

  Nachiketh Karanth

  Resolved

  Part Number: TPS62861 Tool/software: Hi Team, I am using TPS628610YCHR regulator IC. Output of this IC is connected directly to FPGA and nowhere else. By default the IC's output voltage is set to 1.1V through VSEL pin and 5V is input to IC. When regulator…

  • Resolved

  • 8 months ago
  • Power management
  • Power management forum
Answered

• TPS62861: Low vin application

  

  Jeff YANG

  Resolved

  Part Number: TPS62861 Tool/software: Hi, Is there have any solution can support Vin 0.8V to Vout 0.6V(0.6A)? I have check on TI website but can't find suitable solution. Thanks!

  • Resolved

  • over 1 year ago
  • Power management
  • Power management forum

• TPS62861: Low vin application

  

  Jeff YANG

  Part Number: TPS62861 Tool/software: Hi, Is there have any solution can support Vin 0.8V to Vout 0.6V(0.6A)? I have check on TI website but can't find suitable solution. Thanks! Jeff

  • over 1 year ago
  • Interface
  • Interface forum
Answered

• TPS62861: TPS628610YCHR Design Queries

  

  Nachiketh Karanth

  Resolved

  Part Number: TPS62861 Hi, 1. What is the I2C voltage level, 1.8V or 3.3V? 2. Where should VSEL be connected, VCC or GND or can be left floating? Regards, Nachiketh Karanth

  • Resolved

  • over 1 year ago
  • Power management
  • Power management forum

• TPS62861: Schematics Verification for TPS628610YCHR

  

  Nachiketh Karanth

  TI Thinks Resolved

  Part Number: TPS62861 Other Parts Discussed in Thread: USB2ANY Hi, 1. Please verify the below attached schematics, Vin - 5V, Vout - 1.1V 2. Whether all the voltages mentioned in the table are configurable? /cfs-file/__key/communityserver-discussions…

  • over 1 year ago
  • Power management
  • Power management forum

• TPS62861: power good signal

  

  Connie Lu1

  TI Thinks Resolved

  Part Number: TPS62861 Other Parts Discussed in Thread: TPS61240 Hi team, My customer would like to use the TPS628601 power good signal drive the enable of the TPS61240 to sequence the two power rails. Section 8.3.9 in the DS says that the signal can…

  • over 4 years ago
  • Power management
  • Power management forum
Answered

• TPS62861: OVERCURRENT PROTECTION Value of TPS628600

  

  Takashi Yamaguchi

  Resolved

  Part Number: TPS62861 Hi team, My customer is interested in the TPS628600. The datasheet doesn't describe the overcurrent value for the TPS628600. Is it same value as TPS628601? Regards, Yamaguchi

  • Resolved

  • over 5 years ago
  • Power management
  • Power management forum
Answered

• TPS62861: Mechanical drawing with dimensions for YCH package

  

  Don Foong

  Resolved

  Part Number: TPS62861 Hi Team, One of our customer is using TPS62810YCHR, they requested for its mechanical dimensions. Can you share the mechanical drawing with dimensions for the YCH package? Thanks in advance.

  • Resolved

  • over 5 years ago
  • Power management
  • Power management forum

• TPS62861: what the difference between startup time in datasheet

  

  Yuan Tan63

  TI Thinks Resolved

  Part Number: TPS62861 Hi, customer want to find a part with small delay between Vin and Vout. Vin=5V, Vout=3.3V, Ioutmax=500mA. EN is connect with Vin through dividers. delay between Vin and Vout should be <500us. I check TPS62861, which one…

  • over 5 years ago
  • Power management
  • Power management forum

• RE: TPS62097-Q1: Recommend the P2P part with TPS62097QWRGTRQ1

  

  Moheddin Pasha Shaik

  Hi Max, Unfortunately, we don't have any device in our portfolio which can meet your requirements. We do have some devices(not P2P with TPS62097Q) , which can work at minimum VIN of 1.8V, but the maximum output current is lower (IOUT= 1A). TPS62861…

  • 5 months ago
  • Power management
  • Power management forum

Didn't find what you are looking for? Post a new question.