Answered

• TPS7A7100: PG statue when EN=0

  

  Lin_Charles

  Resolved

  Part Number: TPS7A7100 Hi team, When EN=0, and I pull up PG to VCC, how about the statue of this pin? Will it be in low state or follow the VCC signal? Thanks.

  • Resolved

  • over 7 years ago
  • Power management
  • Power management forum

• Compiler/TCA9535: TCA9535: No problem using TPS7A7100?

  

  무성 김

  TI Thinks Resolved

  Part Number: TCA9535 Other Parts Discussed in Thread: TPS7A7100 , Tool/software: TI C/C++ Compiler hi, I would like to use TPS7A7100 LDO in my board design. I want to use I / O control as TCA9535. I will try to use SMBUS type chip for the first…

  • over 7 years ago
  • Interface
  • Interface forum
Answered

• TPS7A7100: 0.9V VOUT LDO

  

  Premsagar Kittur

  Resolved

  Part Number: TPS7A7100 Other Parts Discussed in Thread: TPS7A90 , TPS7A84A Hello, I am looking for an LDO with Min Vout = 0.8V to Max Vout = 1.2V. Vin is adjustable (always greater than 2V). Iload expected is about 100mA. It is for an application running…

  • Resolved

  • over 8 years ago
  • Power management
  • Power management forum
Answered

• RE: TPS7A7100: 0.9V VOUT LDO

  

  Premsagar Kittur

  Resolved

  Sure.. Thank you!

  • over 8 years ago
  • Power management
  • Power management forum

• TPS7A7100: Controlled by PCA9536

  

  Lars Tischendorf

  Part Number: TPS7A7100 Other Parts Discussed in Thread: PCA9536 , PCA9557 I will controlled the output voltage of TPS7A7100 by i2c iio expander. Discribed in App Note: http://www.ti.com/lit/an/sbva035a/sbva035a.pdf I will switch between 1.2 and 1…

  • over 8 years ago
  • Power management
  • Power management forum

• TPS7A7100: About startup problem

  

  Tsukui Yusuke

  TI Thinks Resolved

  Part Number: TPS7A7100 Other Parts Discussed in Thread: TPS7A91 , TPS7A83A , TPS74701 , LP5907 , TLV717P Hi, When the output voltage is activated under the negative voltage condition, the output does not rise. Does this device support negative voltage…

  • over 8 years ago
  • Power management
  • Power management forum

• TPS7A7100: thermal info

  

  Chetan Maheshwari

  Part Number: TPS7A7100 Hi, Thermal Information for TPS7A7100RGT specifies ThetaJA = 44.6 degC/W & ThetaJC= 54.3degC/W. This information doesn't seem to be correct. Please clarify how ThetaJA is less than ThetaJC. Is it a typo or wrong assumption…

  • over 9 years ago
  • Power management
  • Power management forum
Answered

• TPS7A7100: Output capacitor larger than 200uF

  

  Mark Dahlman

  Resolved

  Part Number: TPS7A7100 Other Parts Discussed in Thread: TPS7A91 , TPS7A83A The datasheet for the TPS7A7100 recommends an output capacitor between 4.7uF and 200uF. However I have an application that needs 2200uF of output capacitance. Is there any issues…

  • Resolved

  • over 8 years ago
  • Power management
  • Power management forum

• TPS7A7100 - Accuracy

  

  Mike Ulrich

  Other Parts Discussed in Thread: TPS7A7100 Hi, There is a note on the TPS7A7100 that states "The bottom side of feedback resistor R2 in Figure 28 must be in the range of 27 kΩ to 33 kΩ to maintain the specified regulation accuracy." How does this…

  • over 9 years ago
  • Power management
  • Power management forum

• Layout example of TPS7A7100

  

  takahiko yokota

  Other Parts Discussed in Thread: TPS7A7100 Hi In datasheet, there is the layout example of RGW. If there is layout example of RGT, could you give me it? Best regards, Yokota

  • over 9 years ago
  • Power management
  • Power management forum

Didn't find what you are looking for? Post a new question.