• TS3USBA225: DCR Loss

  

  Allan Fan

  TI Thinks Resolved

  Part Number: TS3USBA225 Hi experts, Customer is inquiring about the maximum DCR loss of TS3USBA225. Their concern is that the low voltage levels of eUSB2 they used may lead to logic level recognition errors at the receiver side if the voltage drop is…

  • 29 days ago
  • Switches & multiplexers
  • Switches & multiplexers forum
Answered

• TS3USBA225: TS3USBA225 USB HUB Interface

  

  Aakash Dey

  Resolved

  Part Number: TS3USBA225 Other Parts Discussed in Thread: TS3DS10224 Hi, We have selected USB MUX TS3USBA225 (1:3) for one of our appilcation. The interfaces are as follows: 1. D0 Port: It is connected to D+, D- pin of FS port of an MCU (STM32H747…

  • Resolved

  • over 2 years ago
  • Interface
  • Interface forum

• TS3USBA225: TS3USBA225

  

  karthik Pillai

  TI Thinks Resolved

  Part Number: TS3USBA225 Other Parts Discussed in Thread: TS3USB3031 Actually in one of our design we want to implement 3:1 MUX/DEMUX, where we want to implement the design for USB signals, Hereby with these matter i am attaching my design also please…

  • over 4 years ago
  • Interface
  • Interface forum
Answered

• TS3USBA225: Asking for the TS3USBA225 and TS3USB221DRC design review

  

  SHH

  Resolved

  Part Number: TS3USBA225 Other Parts Discussed in Thread: TS5A22364 Hi Sir, My customer would like design TS3USBA225 and TS3USB221DRC. U5002/U5005/U5008 Would you please review schematic and provide your comment? BR, SHH

  • Resolved

  • over 4 years ago
  • Interface
  • Interface forum

• TS3USBA225: 3ch for audio application

  

  Gary Teng

  TI Thinks Resolved

  Part Number: TS3USBA225 Hi all, My customer want to find dual SP3T solution. Is TS3USBA225 ok for audio application? Or any other suggestion? Thanks for your kindly help. Regards Gary Teng

  • over 4 years ago
  • Interface
  • Interface forum

• TS3USBA225: TS3USBA225 good but need a mic input as well

  

  Dan Ringger

  TI Thinks Resolved

  Part Number: TS3USBA225 Other Parts Discussed in Thread: TS5USBA224 , TS3USBCA4 I am tasked with finding parts for use with USB audio. I have a few requirements for an analog switch and hope you can recommend a part: 1. 3:1 switch that takes USB 2…

  • over 7 years ago
  • Interface
  • Interface forum

• TS3USBA225: D+/R and D-/L Abs Max in Power Down Mode

  

  Jon Key

  TI Thinks Resolved

  Part Number: TS3USBA225 Hi Team, Could you confirm the abs max of the D+/R and D-/L pins in power down mode? Could they tolerate seeing 5V on the input in power down mode? This is not mentioned in the datasheet, but the abs max of D0+,D0-, D1+, D1…

  • over 5 years ago
  • Interface
  • Interface forum

• TS3USBA225: Asking for the TS3USBA225 schematic review

  

  SHH

  TI Thinks Resolved

  Part Number: TS3USBA225 Hi Team, Customer feedback the device sometimes cannot work properly. Could you please help review TS3USBA225 schematic again? Thanks, SHH

  • over 8 years ago
  • Interface
  • Interface forum

• TS3USBA225: TS3USBA225: U7 switch to Audio mode. Add 20-20KHz, 100mV sweep signal between pin8 and pin10, Pin6 and pin12 are highly distorted, up to 30%.

  

  2018

  TI Thinks Resolved

  Part Number: TS3USBA225 If attached When inserting Line in, Figure 1 is grounded. The Q2 S and D poles are conductive. The chip U7 Pin 3 VCC is connected to the battery voltage of 3.7V, and Pin11 SEL1 is also raised through resistance R16. Vbus is suspended…

  • over 6 years ago
  • Interface
  • Interface forum

• TS3USBA225: TS3USBA225: TS3USBA225RUTR From U7 pin8 and pin10 plus 20-20KHz, 100mV sweep signal, pin6 and pin12 have very high distortion, up to 30%.

  

  2018

  Part Number: TS3USBA225 When inserting Line in, Figure 1 is grounded. The Q2 S and D poles are conductive. The chip U7 Pin 3 VCC connects battery voltage 3.7V. Meanwhile, Pin 11 SEL1 is also elevated through resistance R16. Vbus is suspended, so…

  • over 6 years ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.